Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 2 [3] 4  All

Author Topic: Carlini handlebars on my Breakout  (Read 21976 times)

0 Members and 1 Guest are viewing this topic.

jlsnyderCVO

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 93
Re: Carlini handlebars on my Breakout
« Reply #30 on: May 10, 2013, 04:21:21 PM »

Hi i have a question about the bars, do the standard control cables fit ?.

The controls do fit and these bars are designed for the 'drive-by-wire', however the clamps will need to be changed out due to the step down on the OEM bars, and you will have to extend the brake line a few inches.  I haven't looked into new clamps yet, so I'm dealing with the gap this week. 

Actually no one will even notice the clamp issue, unless I point it out...
Logged
2013 CVO Breakout - SE120R
[/URL]
Please find my introduction post here:jlsnyderCVO BREAKOUT

NewBreak

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
Re: Carlini handlebars on my Breakout
« Reply #31 on: May 17, 2013, 06:30:39 AM »

Hi JL, nice ride.  Question about the risers - are those the stock risers that came with your CVO, or did you replace those when you went with the bars? 
Logged

jlsnyderCVO

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 93
Re: Carlini handlebars on my Breakout
« Reply #32 on: May 17, 2013, 08:05:47 AM »

Hi JL, nice ride.  Question about the risers - are those the stock risers that came with your CVO, or did you replace those when you went with the bars? 

You can't change the riser without reworking the whole electrical system and relocating the speedo/tach combo, and that was the whole reason for picking this particular bar.  I'm not a fan of risers and I would much rather had put a set of clean sweeps on this bike...  :)
Logged
2013 CVO Breakout - SE120R
[/URL]
Please find my introduction post here:jlsnyderCVO BREAKOUT

Dave H

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 238

    • CVO1: 2011 FLHXSE2 ( SESG ) Orange/Black (Sold)
    • CVO2: 2012 FLHXSE3 Ruby Red ( Sadly Sold )
    • CVO3: 2016 FLHXSE3 Black
Re: Carlini handlebars on my Breakout
« Reply #33 on: May 17, 2013, 09:46:33 PM »

Hey Snyd
have you lengthened  the brake line yet to raise the bars a little ?
Or are you going to leave them low and sleek ?
Nice job mate - Every time I look at your bike I like the bars more  :coolblue:
Logged

jlsnyderCVO

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 93
Re: Carlini handlebars on my Breakout
« Reply #34 on: May 18, 2013, 08:11:42 AM »

Hey Snyd
have you lengthened  the brake line yet to raise the bars a little ?
Or are you going to leave them low and sleek ?
Nice job mate - Every time I look at your bike I like the bars more  :coolblue:

Thanks!!

One of my bango fittings was the wrong size and I haven't ordered another one yet, but I think I'll keep the bars in the current location~  :coolblue:
Logged
2013 CVO Breakout - SE120R
[/URL]
Please find my introduction post here:jlsnyderCVO BREAKOUT

Dave H

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 238

    • CVO1: 2011 FLHXSE2 ( SESG ) Orange/Black (Sold)
    • CVO2: 2012 FLHXSE3 Ruby Red ( Sadly Sold )
    • CVO3: 2016 FLHXSE3 Black
Re: Carlini handlebars on my Breakout
« Reply #35 on: June 19, 2013, 04:53:02 PM »

Snyd I think you said there was a small gap each side of clamp?
Or did the Carlinis just bolt straight on?
If not have you covered the gap somehow?
Cheers mate
Logged

jlsnyderCVO

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 93
Re: Carlini handlebars on my Breakout
« Reply #36 on: June 20, 2013, 08:35:13 AM »

Snyd I think you said there was a small gap each side of clamp?
Or did the Carlinis just bolt straight on?
If not have you covered the gap somehow?
Cheers mate

Dave,  I completely forgot about this issue until you brought it up! The bars fit fine with only the addition of the longer brake line and the only way to resolve the controls clamp is by replacing the controls, but for now it's not that big of an deal with me.   I can snap a picture of the problem this afternoon if you would like to see it?
Logged
2013 CVO Breakout - SE120R
[/URL]
Please find my introduction post here:jlsnyderCVO BREAKOUT

wpk

  • Newbie
  • *
  • Offline Offline
  • Posts: 30
Re: Carlini handlebars on my Breakout
« Reply #37 on: June 20, 2013, 09:56:38 AM »

This is my solution to the hardware sticking out .I made new nuts and anodized them black.

Must have the passenger pillion off so that beautiful wide fender can be seen.  I had the stock bolts powder coated...looks much improved.
Logged

Dave H

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 238

    • CVO1: 2011 FLHXSE2 ( SESG ) Orange/Black (Sold)
    • CVO2: 2012 FLHXSE3 Ruby Red ( Sadly Sold )
    • CVO3: 2016 FLHXSE3 Black
Re: Carlini handlebars on my Breakout
« Reply #38 on: June 20, 2013, 04:45:39 PM »

Dave,  I completely forgot about this issue until you brought it up! The bars fit fine with only the addition of the longer brake line and the only way to resolve the controls clamp is by replacing the controls, but for now it's not that big of an deal with me.   I can snap a picture of the problem this afternoon if you would like to see it?

That would be great Snyd . No rush . Thanks big fella  :2vrolijk_21:
Logged

Sandman69

  • Newbie
  • *
  • Offline Offline
  • Posts: 25

    • CVO1: 2013 hard candy breakout with carlini evil apes
Re: Carlini handlebars on my Breakout
« Reply #39 on: June 22, 2013, 09:23:46 AM »

Check these out.  Like they were made for the bike!
Logged

Sandman69

  • Newbie
  • *
  • Offline Offline
  • Posts: 25

    • CVO1: 2013 hard candy breakout with carlini evil apes
Re: Carlini handlebars on my Breakout
« Reply #40 on: June 22, 2013, 09:26:34 AM »

Whoa
Logged

Sandman69

  • Newbie
  • *
  • Offline Offline
  • Posts: 25

    • CVO1: 2013 hard candy breakout with carlini evil apes
Re: Carlini handlebars on my Breakout
« Reply #41 on: June 22, 2013, 09:27:33 AM »

Badazz
Logged

Sandman69

  • Newbie
  • *
  • Offline Offline
  • Posts: 25

    • CVO1: 2013 hard candy breakout with carlini evil apes
Re: Carlini handlebars on my Breakout
« Reply #42 on: June 22, 2013, 09:30:17 AM »

Can't wait till my pipes show up! Hard candy EYE candy!!
Logged

Rocketman69

  • Mr. Roboto
  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 118

    • CVO1: 2012 FLHXCUSE3 Hot Citrus/Antique Gunstock
Re: Carlini handlebars on my Breakout
« Reply #43 on: June 22, 2013, 09:57:55 AM »

Love the look of those Carlini's on your bike......but a quick question to you Breakout guys.....

On my CVO Street Glide, there is a flap built into the back of the rider's seat that is folded in to allow the passenger pillion to attach to the mounting studs.  Once you remove the pillion, all you gotta do to hide the studs is reach in and pull that flap out over the studs.....most people didn't even realize the seat has this feature for months after purchase.......Do your seats not have the same flap??
Logged

CowboyBagger

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1143
  • Standing on the Corner!
    • AZ


    • CVO1: FLHXSE3 Ruby Red/Typhoon Maroon
    • CVO2: FLTRKSEANV Heritage paint
Re: Carlini handlebars on my Breakout
« Reply #44 on: June 22, 2013, 04:12:32 PM »

No flap, just ugly studs.  Poor design by HD to make a good looking solo seat.

I'm waiting for Corbin to come out with their solo with passenger pillion later this summer.

Cowboy
Logged
From an ocean tide, to an 8 second ride! Life is a ride, so make it a good one.
Pages: 1 2 [3] 4  All
 

Page created in 0.266 seconds with 25 queries.