Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 2 3 [All]

Author Topic: SE 120R Fullsac X Pipe dyno test!  (Read 14302 times)

0 Members and 1 Guest are viewing this topic.

Fullsac Performance

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1753
  • Never ride with a Halfsac! Insist on Fullsac Perf!
    • AZ

    • Fullsac Performance
SE 120R Fullsac X Pipe dyno test!
« on: April 09, 2011, 11:55:57 AM »

Here is a 120R dyno chart sent to me from Al at Hot Rod Harley Davidsons, located in the great state of Michigan.
Al is a top notch service and dyno tech who I have worked with for a few years.

The 120R crate engine was installed in a customers 09 Street Glide with a Fullsac "B" X Pipe, Rinehart mufflers and HD Heavy Breather AC.
Typicall smooth X Pipe TQ curve with almost 1.1 HP per cube! Not bad for something that came from an HD catalog.
I'd really like to see one of these 120Rs with a little less compression, smaller cam profile, and the TQ line clearing 125 at 2500.
That would be a Touring motor.

Steve George
Fullsac Performance


Logged
Steve@fullsac.com  www.fullsac.com
Never argue with idiots. They will beat you with experience.

timtoolman

  • never enough torque!!!!!!!
  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 447

    • CVO1: Hillside Stg 4 117, S&S 66 T.B. Woods 400-6, Rush 2-1 Wrath
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #1 on: April 10, 2011, 10:38:19 PM »

I want of them tooooooooo
Logged

Dan_Lockwood

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2497
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #2 on: April 11, 2011, 03:01:36 PM »

Here is a 120R dyno chart sent to me from Al at Hot Rod Harley Davidsons, located in the great state of Michigan.
Al is a top notch service and dyno tech who I have worked with for a few years.

The 120R crate engine was installed in a customers 09 Street Glide with a Fullsac "B" X Pipe, Rinehart mufflers and HD Heavy Breather AC.
Typicall smooth X Pipe TQ curve with almost 1.1 HP per cube! Not bad for something that came from an HD catalog.
I'd really like to see one of these 120Rs with a little less compression, smaller cam profile, and the TQ line clearing 125 at 2500.
That would be a Touring motor.

Steve George
Fullsac Performance

 

Steve, that shows as run file .001.  Do you think he just put it up on the dyno and did one pull and that's what he got?

Logged
Dan

2009 SERG Orange / Black
Board Track Racer Project, Ultima 113"/6spd
2021 Coleman UT400 Side By Side

mrmagloo

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1953
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #3 on: April 11, 2011, 03:05:19 PM »

Any thoughts on that low 2K torque dip?  I thought the other dyno sheet on 120R that was posted recently showed 100 ft/lbs torque at 2,000 on up with a nice straight curve. Just wondering what might be different? Thanks!
Logged
2004 SE Deuce - Cobalt Blue
2006 SE Ultra Classic - Autumn Haze

Fullsac Performance

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1753
  • Never ride with a Halfsac! Insist on Fullsac Perf!
    • AZ

    • Fullsac Performance
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #4 on: April 11, 2011, 03:57:42 PM »

 

Steve, that shows as run file .001.  Do you think he just put it up on the dyno and did one pull and that's what he got?


It does seem odd than it shows run 001. I'm sure this was the best run after quite a few dyno pulls.
Maybe he didn't want anyone to know how many pulls it took?

SG
Logged
Steve@fullsac.com  www.fullsac.com
Never argue with idiots. They will beat you with experience.

Dr.D

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1109

    • CVO1: 09 SEDFB Sunrise Yellow and Black Quartz
    • CVO2: 2014 CVO Limited silver/orange
    • CVO3: 2015 Indian Vintage Custom 57 Chevy Blue
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #5 on: April 11, 2011, 04:03:45 PM »

Any thoughts on that low 2K torque dip?  I thought the other dyno sheet on 120R that was posted recently showed 100 ft/lbs torque at 2,000 on up with a nice straight curve. Just wondering what might be different? Thanks!

I did not like the bottom of the tq curve either. Are the pipes/mufflers giving enough back pressure? What kind of compression does the motor have? Why smaller cam profile? Early intake would help right?
Logged

Fullsac Performance

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1753
  • Never ride with a Halfsac! Insist on Fullsac Perf!
    • AZ

    • Fullsac Performance
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #6 on: April 11, 2011, 04:09:25 PM »

Any thoughts on that low 2K torque dip?  I thought the other dyno sheet on 120R that was posted recently showed 100 ft/lbs torque at 2,000 on up with a nice straight curve. Just wondering what might be different? Thanks!
A slight take off dip is very common as the accelerator pump floods the motor for a second. I usually start my pulls at 1700 with a roll on
to try to get the fuel cleared out by 2000 rpm. With the huge cams in the 120R I'm surprised it as smooth as it is. Again, I would really like to see this
combo with a smaller cam to bring on the early TQ that is available with 120 CI motor. I've seen dynos from a 124" motor with my B X Pipe
that showed 143 peak TQ, 120 TQ at 2500 with 125 peak HP. That's a nice TQ curve for a Touring motor!

Steve George
Fullsac Performance
Logged
Steve@fullsac.com  www.fullsac.com
Never argue with idiots. They will beat you with experience.

Fullsac Performance

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1753
  • Never ride with a Halfsac! Insist on Fullsac Perf!
    • AZ

    • Fullsac Performance
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #7 on: April 11, 2011, 04:21:03 PM »

I did not like the bottom of the tq curve either. Are the pipes/mufflers giving enough back pressure? What kind of compression does the motor have? Why smaller cam profile? Early intake would help right?
Rinehart mufflers? Cant say what size core it had. It needs 2.25 minimum. In this case, small cores will hurt the TQ.
The HD book says 10.5 comp with SE 266E cams. Those are monsters with a 58 deg closing. Really need about 11.5 and race gas to
even act alive on the bottom. For a Touring motor, all wrong. JMHO.

Steve George
Fullsac Performance
Logged
Steve@fullsac.com  www.fullsac.com
Never argue with idiots. They will beat you with experience.

Dr.D

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1109

    • CVO1: 09 SEDFB Sunrise Yellow and Black Quartz
    • CVO2: 2014 CVO Limited silver/orange
    • CVO3: 2015 Indian Vintage Custom 57 Chevy Blue
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #8 on: April 12, 2011, 12:44:47 PM »

Rinehart mufflers? Cant say what size core it had. It needs 2.25 minimum. In this case, small cores will hurt the TQ.
The HD book says 10.5 comp with SE 266E cams. Those are monsters with a 58 deg closing. Really need about 11.5 and race gas to
even act alive on the bottom. For a Touring motor, all wrong. JMHO.

Steve George
Fullsac Performance

Thanks for the response. I have seen the spec on those 266e and they are bit big and biased to the high rpm hp and not right on the big tourer. I would think the 10.5 comp is as much as you would want on a street bike running the average high test unleaded. I need to look at the header pipes and ask if there is a web site.?
Logged

ultraswede

  • Guest
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #9 on: April 12, 2011, 01:51:35 PM »

This bike is EFI, so there is no acc-pump.
The acc enrichment is very easy to tune in the EFI,
so personally I don't believe that is the reason for the dip.
Logged

Fullsac Performance

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1753
  • Never ride with a Halfsac! Insist on Fullsac Perf!
    • AZ

    • Fullsac Performance
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #10 on: April 12, 2011, 04:23:12 PM »

Thanks for the response. I have seen the spec on those 266e and they are bit big and biased to the high rpm hp and not right on the big tourer. I would think the 10.5 comp is as much as you would want on a street bike running the average high test unleaded. I need to look at the header pipes and ask if there is a web site.?

The Fullsac X Pipe can be seen at www.fullsac.com.

SG
Logged
Steve@fullsac.com  www.fullsac.com
Never argue with idiots. They will beat you with experience.

Fullsac Performance

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1753
  • Never ride with a Halfsac! Insist on Fullsac Perf!
    • AZ

    • Fullsac Performance
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #11 on: April 12, 2011, 04:31:41 PM »

This bike is EFI, so there is no acc-pump.
The acc enrichment is very easy to tune in the EFI,
so personally I don't believe that is the reason for the dip.
Yes, it is EFI. It does have an accelerator pump or "accel enrichment" if you prefer.
Sorry to disagree, they are a pain in the ass if not impossible to make perfect everywhere at all throttle roll ons, especially if you have
big cams as noted in this engine. Again, JMHO.

Steve George
Fullsac Performance
Logged
Steve@fullsac.com  www.fullsac.com
Never argue with idiots. They will beat you with experience.

HILLSIDECYCLE.COM

  • Banned
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2085
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #12 on: April 13, 2011, 07:24:37 AM »

A slight take off dip is very common as the accelerator pump floods the motor for a second. I usually start my pulls at 1700 with a roll on
to try to get the fuel cleared out by 2000 rpm. With the huge cams in the 120R I'm surprised it as smooth as it is. Again, I would really like to see this
combo with a smaller cam to bring on the early TQ that is available with 120 CI motor. I've seen dynos from a 124" motor with my B X Pipe
that showed 143 peak TQ, 120 TQ at 2500 with 125 peak HP. That's a nice TQ curve for a Touring motor!

Steve George
Fullsac Performance

I agree with Steve.
I doubt if the pipe is really responsible for anything, coming off the bottom.
Those 120's need a tune-up in the cam dept., or more compression to support that late-blooming 266.
Scott
Logged

cvosjoe

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 630
    • Joe's Place
Re: Re: Re: SE 120R Fullsac X Pipe dyno test!
« Reply #13 on: November 04, 2011, 10:08:03 AM »

Here is a 120R dyno chart sent to me from Al at Hot Rod Harley Davidsons, located in the great state of Michigan.
Al is a top notch service and dyno tech who I have worked with for a few years.

The 120R crate engine was installed in a customers 09 Street Glide with a Fullsac "B" X Pipe, Rinehart mufflers and HD Heavy Breather AC.
Typicall smooth X Pipe TQ curve with almost 1.1 HP per cube! Not bad for something that came from an HD catalog.
I'd really like to see one of these 120Rs with a little less compression, smaller cam profile, and the TQ line clearing 125 at 2500.
That would be a Touring motor.

Steve George
Fullsac Performance

Steve,
Do you know if the stock 50mm TB was used or did they go with a larger one?
Logged
2019 FLHXSE Charred Steel/Lightning Silver
2018 FLHXSE - Totaled
2017 FLTRXS Wicked Red Denim
2017 FLHXSE - Traded
2015 FLTRUSE - Traded
2014 FLHTKSE - Traded
2013 FLHTCUSE8 - Traded
2012 FLTRXSE - Sold
2011 FLTRUSE - Traded
2009 FLTRSE3 - Traded
2005 FLHTCSE2 - Traded
2004 FXSTDSE2 - Traded

willyB

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1128
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #14 on: November 04, 2011, 11:43:12 AM »

My wife and I have unfortunately became unemployed earlier this year. You know, economy etc...

Since I have nothing but time on my hands now I would be more than willing to "test out" a new 120R on my 2011 CVO Street Glide and provide the results back to this forum on a daily basis. If anyone wants to send me a new 120R I will install it and begin the results feedback. If you can't send it I will be more than willing to come and pick it up.

 ;D
Logged
GMR 577 Cams, S & S Lifters, S & S Pushrods, V&H Headers, Rinehart 4” Slipons, TTS Tuner, 12" Yaffee Monkey Bars, Color Matched Chopped Tour Pak (510 HP and 763 TQ +/-)

cvosjoe

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 630
    • Joe's Place
Re: Re: Re: SE 120R Fullsac X Pipe dyno test!
« Reply #15 on: November 04, 2011, 12:28:55 PM »

:2vrolijk_21: I agree. It is not the AE table that causes a rich dip below 2500 rpm. Here is another 09 FLHX with a 120r right out of the crate.

What exhaust and TB are you using on this?
Logged
2019 FLHXSE Charred Steel/Lightning Silver
2018 FLHXSE - Totaled
2017 FLTRXS Wicked Red Denim
2017 FLHXSE - Traded
2015 FLTRUSE - Traded
2014 FLHTKSE - Traded
2013 FLHTCUSE8 - Traded
2012 FLTRXSE - Sold
2011 FLTRUSE - Traded
2009 FLTRSE3 - Traded
2005 FLHTCSE2 - Traded
2004 FXSTDSE2 - Traded

lonewolf55

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 75
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #16 on: November 04, 2011, 02:14:04 PM »

SE 58, Supertrapp 2:1. 35 disc's closed cap. He wanted quiet.
Logged

HD Street Performance

  • Vendor
  • 2.5K CVO Member
  • *
  • Offline Offline
  • Posts: 3118
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #17 on: November 04, 2011, 03:04:24 PM »

120Rs with a little less compression, smaller cam profile,

It has 10.3:1 actual the 54 you like would accomplish the goal. Would probably drop 12hp and gain peak torque of 5 or so and shift it to the right.
Logged

Doc 1

  • Doc 1
  • Vendor
  • Elite CVO Member
  • *
  • Offline Offline
  • Posts: 613
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #18 on: November 04, 2011, 03:45:11 PM »

If the dip was made by the flooding of the accel table your AFR line would show a rich condition in the same area. The overlap from the cam coupled with low compression and piston speed slower than the air intake speed will make this dip at that low rpm. If it were pipes the dip would be at 2500 rpm area. This is over a 650 lift cam.....they don't work at 2000 rpm.
Doc
Logged
Doc's Performance Tuning

www.docsperformancetuning.com

North Star

  • CANADA- Love it or Leave it
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1678
    • ON


    • CVO1: 2009 CVO Road Glide- Orange/Black
    • CVO2: 2015 Ducati Monter 821- Star White
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #19 on: November 04, 2011, 06:16:01 PM »

Sounds like even the latest greatest 120 is not right out of the crate- it needs to be modded too.
Logged
2009 Screamin' Eagle Road Glide- Electric Orange/Vivid Black
GMR 113", GMR 600 cams, Fullac DX & Kuryakyn Crushers, SE Heavy Breather, tuned by "Dyno Dave" Stoddart
Jagg 10 row fan assisted oil cooler
Axeo Legends/Ohlins 3-3/True Track front and rear
C&C Fastback seat w/orange flame stitching & a Le Pera Maverick
PYO Monkey Bars- 10"
Freedom Shields 12" light grey
Hawg Wired "six pack"amp/speakers, Iron Cross ipod interface
HD Daymaker headlights
Detachable King Tour Pak in Electric Orange

sadunbar

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 11416
  • EBCM # Stealth - SSBS # 1.1 - SoA # Z&E2525 .01%
    • IL


    • CVO1: 2007 FLHTCUSE2
    • CVO2: 2000 FXR4
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #20 on: November 04, 2011, 06:47:41 PM »

Sounds like even the latest greatest 120 is not right out of the crate- it needs to be modded too.

The 120r is fantastic right out of the crate...

Any motor can be improved upon...  And any motor can be altered to suit particular riding styles...   
Logged
2007 Screamin Eagle Ultra Classic - Light Candy Cherry and Black Ice
Screamin Eagle 120r
Revolution Performance EMS
Fuel Moto Jackpot headpipes and 4.5" Pro Touring Mufflers
HPI 55mm Throttle Body w/5.3 injectors
BDL clutch w/VPC92T
Traxxion AK-20
Legend Air Suspension
Brembo Brake Calipers/Rotors
Garmin Zumo
575 Chubby's
Bushtec Quantum

Fullsac Performance

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1753
  • Never ride with a Halfsac! Insist on Fullsac Perf!
    • AZ

    • Fullsac Performance
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #21 on: November 05, 2011, 01:43:12 AM »

If the dip was made by the flooding of the accel table your AFR line would show a rich condition in the same area. The overlap from the cam coupled with low compression and piston speed slower than the air intake speed will make this dip at that low rpm. If it were pipes the dip would be at 2500 rpm area. This is over a 650 lift cam.....they don't work at 2000 rpm.
Doc

 :2vrolijk_21: :2vrolijk_21: :2vrolijk_21:
Logged
Steve@fullsac.com  www.fullsac.com
Never argue with idiots. They will beat you with experience.

Phaq2

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 76
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #22 on: November 05, 2011, 07:57:55 AM »

I read alot of posts recommending lower profile cams can anybody make any suggestions? What would have been a better choice for a bagger?  Sorry for the hijack...Thanks
Logged

HD Street Performance

  • Vendor
  • 2.5K CVO Member
  • *
  • Offline Offline
  • Posts: 3118
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #23 on: November 05, 2011, 09:20:31 AM »

No change for a bagger. It is a 120 well designed and matched to a heavy bike but still right at home in a lighter chassis. If someone was looking for changes to accelerate better (really??) changing the gearing would help but really this 120 makes good torque surprisingly down low and over a wide range. I stated change to the 54 but if it were mine I would not do that, I would raise the compression a tad though, fix the geometry and add corrected geometry rockers then ride on
Logged

cvobiker

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 2643
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #24 on: November 05, 2011, 01:53:54 PM »

My wife and I have unfortunately became unemployed earlier this year. You know, economy etc...

Since I have nothing but time on my hands now I would be more than willing to "test out" a new 120R on my 2011 CVO Street Glide and provide the results back to this forum on a daily basis. If anyone wants to send me a new 120R I will install it and begin the results feedback. If you can't send it I will be more than willing to come and pick it up.

 ;D

Hey Willy,,, you can pick one up at your nearest HD Dealer.... Hurry Up!! i want to start seeing your results...   :2vrolijk_21:
Logged

Phaq2

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 76
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #25 on: November 05, 2011, 01:58:43 PM »

No change for a bagger. It is a 120 well designed and matched to a heavy bike but still right at home in a lighter chassis. If someone was looking for changes to accelerate better (really??) changing the gearing would help but really this 120 makes good torque surprisingly down low and over a wide range. I stated change to the 54 but if it were mine I would not do that, I would raise the compression a tad though, fix the geometry and add corrected geometry rockers then ride on

Thanks Dewey, My dealer is running a 20% off special so I got a quote yesterday...$4830.17 including local sales tax....... I just may have to pull the trigger.
Logged

willyB

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1128
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #26 on: November 06, 2011, 08:12:03 AM »

Hey Willy,,, you can pick one up at your nearest HD Dealer.... Hurry Up!! i want to start seeing your results...   :2vrolijk_21:
Now all I have to do is raise $4,800+ and I'll be ready to start sending the results.

Hmmmm, anyone know where I can find a job to raise the funds?
 ;D

Man, I would love to have this motor. If anything just to give my brother a little grief.
Logged
GMR 577 Cams, S & S Lifters, S & S Pushrods, V&H Headers, Rinehart 4” Slipons, TTS Tuner, 12" Yaffee Monkey Bars, Color Matched Chopped Tour Pak (510 HP and 763 TQ +/-)

smiley1049

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 401
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #27 on: November 06, 2011, 08:15:59 AM »

But they only come in black!
Logged

eleft36

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 129
  • Senior Rider
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #28 on: November 06, 2011, 05:34:50 PM »

My wife and I have unfortunately became unemployed earlier this year. You know, economy etc...

Since I have nothing but time on my hands now I would be more than willing to "test out" a new 120R on my 2011 CVO Street Glide and provide the results back to this forum on a daily basis. If anyone wants to send me a new 120R I will install it and begin the results feedback. If you can't send it I will be more than willing to come and pick it up.

 ;D

Willy,
I see grants for nothing to do with "the common good" for millions of $$$, give it a try.... call your senator. :jack:
Logged
2010 CVO 110" Conv. Exhaust, K&N A/C, Stock Heads, SE 103" BB kit, Andrews 26H Cams, Adapted H-D Engine Guard, Mustang wide Touring Seat, Stock Bars, H-D Oil Cooler, 1990 Leather Works Inc. Bags with Deluxe modified guards, H-D Windshield, Thunder Max A/T, '05 CVO Tour Pac, SCRC Chapter 524

Aceboympk

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 66
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #29 on: November 06, 2011, 08:55:30 PM »

Thanks Dewey, My dealer is running a 20% off special so I got a quote yesterday...$4830.17 including local sales tax....... I just may have to pull the trigger.

$4800 for a 120R engine?  Well, my bike has 37k miles on her, so I know what I'll be replacing that engine with.  ;-)

Maybe Willy can come over to my house and help me with the install.  Free food and drinks!  Hell, I'll let you take the second ride on her and I don't let anyone on my bikes.

 :help:
Logged

willyB

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1128
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #30 on: November 07, 2011, 11:04:09 AM »

$4800 for a 120R engine?  Well, my bike has 37k miles on her, so I know what I'll be replacing that engine with.  ;-)

Maybe Willy can come over to my house and help me with the install.  Free food and drinks!  Hell, I'll let you take the second ride on her and I don't let anyone on my bikes.

 :help:
Hmmmmmm, free food and drinks? You did read that I'm unemployed.
Logged
GMR 577 Cams, S & S Lifters, S & S Pushrods, V&H Headers, Rinehart 4” Slipons, TTS Tuner, 12" Yaffee Monkey Bars, Color Matched Chopped Tour Pak (510 HP and 763 TQ +/-)

Aceboympk

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 66
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #31 on: November 07, 2011, 11:07:22 AM »

Hmmmmmm, free food and drinks? You did read that I'm unemployed.

I figured you had some time on your hands and what better way to spend that time than installing an 120R engine (you'd be the envy of all your friends) and then going for a ride on her.

Plus food and drinks!!!!  What more can a guy ask for? :2vrolijk_21:
Logged

willyB

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1128
Re: SE 120R Fullsac X Pipe dyno test!
« Reply #32 on: November 07, 2011, 03:05:41 PM »

I figured you had some time on your hands and what better way to spend that time than installing an 120R engine (you'd be the envy of all your friends) and then going for a ride on her.

Plus food and drinks!!!!  What more can a guy ask for? :2vrolijk_21:
I'm sorry. I was taking my mid day nap.
Logged
GMR 577 Cams, S & S Lifters, S & S Pushrods, V&H Headers, Rinehart 4” Slipons, TTS Tuner, 12" Yaffee Monkey Bars, Color Matched Chopped Tour Pak (510 HP and 763 TQ +/-)
Pages: 1 2 3 [All]
 

Page created in 0.239 seconds with 24 queries.