www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Loose end cap on grip  (Read 10089 times)

0 Members and 1 Guest are viewing this topic.

Lennyiti

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 85

    • CVO1: 2008 FXDSE2
    • CVO2: 2011 FLSTSE2
Loose end cap on grip
« on: October 09, 2007, 02:07:25 PM »
Any one have the end cap come loose on left side of handle bar? Mine is now loose and I don't see any way to tighten it? The thing rattles going down the road. Any ideas?
Logged

Midnight Rider

  • AKA: TCnBham
  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 11107
  • FLHRSEI.ORG

    • CVO1: 2011 SERGU Rio Red (sold)
Re: Loose end cap on grip
« Reply #1 on: October 09, 2007, 02:20:16 PM »
Quote from: Lennyiti on October 09, 2007, 02:07:25 PM
Any one have the end cap come loose on left side of handle bar? Mine is now loose and I don't see any way to tighten it? The thing rattles going down the road. Any ideas?

Loosen the two Torx screws that hold the switches/clutch assembly on and pull the grip off (it's not glued), look inside to see if there is a way to tighten it.  If not, get the dealer to replace or glue the end on with Gorilla Glue...that stuff is amazing!!
Logged
Sometimes it takes a whole tankful of fuel before you can think straight.
I had the right to remain silent, just not the ability...

Gone, but not forgotten...2011 FLTRUSE with
Fullsac X Pipe w/2" Baffles
Legend Air Ride Rear Shocks
Traxxion Dynamics AK-20 Front Suspension
Clearview GT13 Windshield
TTS Mastertune

Boatman

  • 2.5K CVO Member
  • **
  • Online Online
  • Posts: 4810
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: Loose end cap on grip
« Reply #2 on: October 09, 2007, 07:19:27 PM »
My 05 stock grip ends were loose.  I had them off while I installed the Heat Demon heaters.   I found that my end caps pop off and there is a nut on the inside of each end cap that you can tighten.  Actually you squeeze the plastic tabs around the nut (to keep the nut from turning) and turn the chrome end cap with your other hand to tighten.  If your stock grips are made like mine, this will work.  Then just pop the end cap back in the grip.  You don't have to remove the grip to do this, just pop off the end cap with a small screwdriver.  Good luck.   :2vrolijk_21:
Logged

bpalmersheim

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 248

    • CVO1: '07 CVO Screamin' Eagle Road King (FLHRSE3) 110" - Razor Red/Gold Leaf Flames
Re: Loose end cap on grip
« Reply #3 on: October 18, 2007, 07:41:26 PM »
I actually lost the end cap on the throttle grip I heard it hit the ground when I was on the Interstate.  Realized what hit the ground when I got home and noticed the cap missing.  I guess MoCo will have to replace the grip under warranty!
Logged
2007 CVO Screamin' Eagle Road King (FLHRSE3) 110" - Razor Red/Gold Leaf Flames

United States Army Retired (4x Combat Veteran)
CVMA, H.O.G. Member, Patriot Guard Rider

Rides2007Harley

  • Guest
Re: Loose end cap on grip
« Reply #4 on: October 20, 2007, 08:27:49 AM »
There is an easy fix for this as they work loose after a while.  Pull the end cap off and simply tighten the nut a bit that holds the end cap in place.  Takes about a minute to do.
Logged

Tbone

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1491
  • FLHRSEI.ORG

    • CVO1: 2008 FLHTCUSE3
    • CVO2: 2009 FLTRSE3
    • CVO3: 2013 FLHTCUSE8
Re: Loose end cap on grip
« Reply #5 on: October 20, 2007, 08:31:02 AM »
Quote from: Boatman on October 09, 2007, 07:19:27 PM
My 05 stock grip ends were loose.  I had them off while I installed the Heat Demon heaters.   I found that my end caps pop off and there is a nut on the inside of each end cap that you can tighten.  Actually you squeeze the plastic tabs around the nut (to keep the nut from turning) and turn the chrome end cap with your other hand to tighten.  If your stock grips are made like mine, this will work.  Then just pop the end cap back in the grip.  You don't have to remove the grip to do this, just pop off the end cap with a small screwdriver.  Good luck.   :2vrolijk_21:

What Bob said.  Don Tilley showed me that trick.

Bob
Logged
2014 FLHTKSE Stardust Silver/Autumn Sunset
2013 FLHTCUSE8 Anniversary
2009 FLTRSE3 Orange/Black
2008 FLHTCUSE3 Anniversary
2003 FLHRCI Silver/Black

Andrea O

  • Guest
Re: Loose end cap on grip
« Reply #6 on: October 20, 2007, 05:16:59 PM »
I have lost 2

on the left side as well

Just got a new one today for $11.95
Logged

SE08RK

  • Banned
  • Full CVO Member
  • *
  • Offline Offline
  • Posts: 145
Re: Loose end cap on grip
« Reply #7 on: October 30, 2007, 12:43:19 PM »
Quote from: Andrea O on October 20, 2007, 05:16:59 PM
I have lost 2

on the left side as well

Just got a new one today for $11.95

Oh, so that's why HD leaves them loose! $11.95! Needle nose pliers to tighten the nylon nut is the trick.

BC
Logged

soulfly

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 87

    • CVO1: 2013 CVO Road King Anniversary FLHRSE5 #165
    • CVO2: (2007 CVO Dyna Twilight Blue Ice Blue Pearl/Granite)
Re: Loose end cap on grip
« Reply #8 on: January 12, 2008, 01:04:40 PM »
I hav the 07.  Ya Know I never noticed until it fell off.  So I went to buy one, and you cant!  Harley told me no you cant buy one you have to buy a pair of grips!  So told service about it, and after a whats what of "IT JUST FELL OFF" yes, thats what happened, they ordered me one.  It snapped right in.  But the thing is, it does have a part #, but you cant order it???
Logged
THE MORE SERIOUSLY I TOOK THINGS, THE HARDER THE RULES BECAME.

Andrea O

  • Guest
Re: Loose end cap on grip
« Reply #9 on: January 12, 2008, 01:19:04 PM »
yes you can buy one

I will get the item # for you

Andrea
Logged

fxdsebeloved

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 147
  • Four Wheels Move The Body Two Wheels Move The Soul

    • CVO1: (Beloved) 2007 FXDSE Silver Rush/Midnight Black
    • alcohaulinasss
Re: Loose end cap on grip
« Reply #10 on: February 01, 2008, 06:10:03 PM »
Mine was comming loose on the throttle side  :-\ pop it off and there is is a screw that expands the rubber grommet to make it tighter (Wider) and pot it back in. Mine hasn't come loose since  :2vrolijk_21:
Logged
Member # 1786
If you live in the past
You will have no future

Yendor1954

  • 2008 Dyna CVO
  • Newbie
  • *
  • Offline Offline
  • Posts: 36

    • CVO1: 2008 Dyna Screamin Eagle
    • CVO2: 1974 Kawasaki Z1 900
Re: Loose end cap on grip
« Reply #11 on: July 24, 2008, 03:34:42 AM »
Hi from Aus

I have a fxdse2 and had the same problem. I pulled the end cap of and there is a little adjuster bolt in the centre that you screw in to expand the catchers then you push it back in and bingo. Hope it works fr your model.   Rod
Logged

FCM

  • Newbie
  • *
  • Offline Offline
  • Posts: 9
Re: Loose end cap on grip
« Reply #12 on: July 29, 2008, 03:09:54 PM »
I should come here more often  :2vrolijk_21: I have now found out how to fix several things wrong? with mine  :huepfenlol2:
Note to self stay off truck sights and log on bike site more. :curtain:
Logged

Andrea O

  • Guest
Re: Loose end cap on grip
« Reply #13 on: September 14, 2008, 09:59:10 PM »
I have got to tighten mine again. It sounds like jingle bells when it is loose.
Logged

SPIDERMAN

  • Guest
Re: Loose end cap on grip
« Reply #14 on: September 14, 2008, 10:20:14 PM »
FYI
     You can buy just the end caps. They come in pairs

B B
Logged
 

Page created in 0.153 seconds with 22 queries.