Topic: WingTip Fairing light/turn install with pictures (Read 17805 times)

Boatman · « **on:** June 10, 2008, 09:41:43 PM »

I purchased and installed the BT40 LED wingtip fairing lights from ElectraGlide Goodies. Once received, I found it to be made by Biketronics and resold by EGoodies. Both of them sell the kit for $99.95 plus shipping.

Below is a picture of the kit as received-2 LED's with wiring, connector plugs, and controller.

They work as a running light and turnsignal that flashes alternate of the MOCO signals.

Boatman · « **Reply #1 on:** June 10, 2008, 09:45:59 PM »

The inner fairing has a rubber u channel sealing gasket. Figure where you want to put the LED's and cut the existing u channel. I used 3M black weatherstrip adhesive to a fix the LED strips and taped them overnight to hold in place. The difference between these LED strips and the other flexible strips you see are that these have the u channel molded in/on them for the install over the inner fairing lip.

On 04's and 05's, you locate the front turnsignal plug and disconnect, and simply plug in the 2 plugs of the LED controller.

Here is a picture of the install with the OUTER fairing still off.

Boatman · « **Reply #2 on:** June 10, 2008, 09:47:01 PM »

Lighted.

Boatman · « **Reply #3 on:** June 10, 2008, 09:47:59 PM »

Another view.

Boatman · « **Reply #4 on:** June 10, 2008, 09:48:52 PM »

Boatman · « **Reply #5 on:** June 10, 2008, 09:49:29 PM »

Boatman · « **Reply #6 on:** June 10, 2008, 09:53:15 PM »

Thus far, I am happy with the result. They can be seen from the side, rear, and to a lesser degree the front. I did not want to drill any holes in the outer fairing for the aftermarket or MOCO lighted windshield strips. If these fail or become a pain in R&R of the outer fairing, they can be easily removed, buy new weatherstrips and I am back to stock.

With the bixenon headlight and driving lights on, you couldn't see the front turnsignals that well. This system at least works for me for now. It won't be for everyone. Naysayers can say their peace too.

cuthbertss · « **Reply #7 on:** June 10, 2008, 09:56:26 PM »

interesting....night photos?

too bad i wont buy anything from EGG

Boatman · « **Reply #8 on:** June 10, 2008, 09:58:12 PM »

Quote from: cuthbertss on June 10, 2008, 09:56:26 PM

interesting....night photos?

too bad i wont buy anything from EGG

I will get some night pictures.

No, they don't have a good reputation but they can also be bought from the maker, Biketronics.

cuthbertss · « **Reply #9 on:** June 10, 2008, 10:20:12 PM »

Quote from: Boatman on June 10, 2008, 09:58:12 PM

I will get some night pictures.

No, they don't have a good reputation but they can also be bought from the maker, Biketronics.

Thanks!

Boatman · « **Reply #10 on:** June 10, 2008, 10:26:38 PM »

I am definitely not a photographer. This was taken in the garage with flash. Regarding brightness, they are definitely brighter than my Kuryakyn LED front turnsignals and brighter than my MOCO LED spoiler lights on bags and tourpack.

Boatman · « **Reply #11 on:** June 10, 2008, 10:28:18 PM »

Hope this helps (no flash).

cuthbertss · « **Reply #12 on:** June 10, 2008, 10:32:39 PM »

Quote from: Boatman on June 10, 2008, 10:28:18 PM

Hope this helps (no flash).

cool

ccr · « **Reply #13 on:** June 11, 2008, 02:39:58 AM »

Bob, that looks GREAT!!!!!!

MUFFMAN · « **Reply #14 on:** June 11, 2008, 06:06:34 AM »

Looks good. More money I have to spend.

Trapperdog · « **Reply #15 on:** June 11, 2008, 10:26:10 AM »

Wasn't too sure about them till I saw you night pic, now I am sold! Damm, there goes another $100. Good pics

HWYMAN1 · « **Reply #16 on:** June 11, 2008, 11:35:56 AM »

Had been debating about these (mostly because eGlide sold them), vs. Mirror signal (ie. Muth). These are definitely cheaper and look much easier to install!

john

Boatman · « **Reply #17 on:** June 11, 2008, 12:18:37 PM »

Thanks for all the positive responses. With the bike not running, they blend in real well to the lines of the fairing and don't stand out. For the additional lighting they provide, they are the simplest/cheapest solution available and still look good on the bike. They can also be fit to a RoadGlide per the manufacturer.

Harleypingman · « **Reply #18 on:** June 11, 2008, 01:16:00 PM »

Thanks for the write-up and pics.

Boatman · « **Reply #19 on:** June 11, 2008, 01:19:02 PM »

Quote from: Harleypingman on June 11, 2008, 01:16:00 PM

Thanks for the write-up and pics.

Someone has to be the guinea pig on a new item. Most of the time it is 2lane.

Garznhogs · « **Reply #20 on:** June 20, 2008, 08:22:47 PM »

Quote from: Boatman on June 10, 2008, 09:45:59 PM

On 04's and 05's, you locate the front turnsignal plug and disconnect, and simply plug in the 2 plugs of the LED controller.

Here is a picture of the install with the inner fairing still off.

Bob, do you end up with stock turnsignals and WingTip operating?
Thanks,
:-Jerry

Keithincda · « **Reply #21 on:** June 20, 2008, 11:15:24 PM »

boatman, any chance you can take a picture from the back of the bike looking forward? The pics you took look great and have me interested but I'm curious how noticeable they are from someone sitting behind the bike...

BALIS · « **Reply #22 on:** June 22, 2008, 09:38:00 AM »

Thanks for the pics.Now I'm convinced that I may order a set for my bike.
Jean

FUZZNUTS · « **Reply #23 on:** June 22, 2008, 10:33:17 AM »

I have a after market faring, I wonder if they could work on mine. These look cool as hell.

mr_magoo · « **Reply #24 on:** June 22, 2008, 11:46:02 AM »

They look nice thanks for all the photos. like the fact that there are no holes to drill. I think I'll send an e mail to biketronic and ask about a group buy, how many would be interested?

Boatman · « **Reply #25 on:** June 22, 2008, 06:10:14 PM »

Quote from: Garznhogs on June 20, 2008, 08:22:47 PM

Bob, do you end up with stock turnsignals and WingTip operating?
Thanks,
:-Jerry

Yes the stock front and rear signals still work and the wingtips flash off sequence with the stock turnignals. When the turnsignals are not on, they are running lights.

Garznhogs · « **Reply #26 on:** June 22, 2008, 07:27:04 PM »

Quote from: Boatman on June 22, 2008, 06:10:14 PM

Yes the stock front and rear signals still work and the wingtips flash off sequence with the stock turnignals. When the turnsignals are not on, they are running lights.

Great... thanks, Bob. And thanks for the write-up and pics.

Mr_Magoo... I'm interested if a group buy happens.

:-Jerry

naitram · « **Reply #27 on:** June 22, 2008, 07:35:17 PM »

Quote from: FUZZNUTS on June 22, 2008, 10:33:17 AM

I have a after market faring, I wonder if they could work on mine. These look cool as hell.

i thougt about it for a few minutes myself but. how would you wire it up to keep things detachable?

Garznhogs · « **Reply #28 on:** June 22, 2008, 08:49:20 PM »

Quote from: naitram on June 22, 2008, 07:35:17 PM

i thougt about it for a few minutes myself but. how would you wire it up to keep things detachable?

If they're attached to the inner fairing, they'd just stay there with all the other junk, wouldn't they? Even tho Bob said "Inner fairing still off" I think he meant 'outer' fairing. At least that's what I think I'm seeing in the photo.

naitram · « **Reply #29 on:** June 22, 2008, 08:52:46 PM »

FUZZNUTS was refering to an aftermarket fairing on a SERK

Garznhogs · « **Reply #30 on:** June 22, 2008, 09:08:52 PM »

Quote from: naitram on June 22, 2008, 08:52:46 PM

FUZZNUTS was refering to an aftermarket fairing on a SERK

Oops.

Sorry. (I do see the problem. Now!)

Boatman · « **Reply #31 on:** June 22, 2008, 09:30:08 PM »

Quote from: Garznhogs on June 22, 2008, 08:49:20 PM

If they're attached to the inner fairing, they'd just stay there with all the other junk, wouldn't they? Even tho Bob said "Inner fairing still off" I think he meant 'outer' fairing. At least that's what I think I'm seeing in the photo.

Thanks for pointing it out, just corrected it.

Boatman · « **Reply #32 on:** June 22, 2008, 09:33:02 PM »

Quote from: Keithincda on June 20, 2008, 11:15:24 PM

boatman, any chance you can take a picture from the back of the bike looking forward? The pics you took look great and have me interested but I'm curious how noticeable they are from someone sitting behind the bike...

Keith, give me a few days and I will do (rear pic). Until then-

From the back and side, you can see the running/turns easily.

DEAD ON from the front, you can see about 1/2 of the run/turns. Get a little off 1-2' either side (from the front) and can easily see the runs/turns.

Keithincda · « **Reply #33 on:** June 22, 2008, 11:13:40 PM »

thanks Boatman... Appreciate the description and the pics if you take them..

Boatman · « **Reply #34 on:** June 23, 2008, 09:19:06 PM »

6-7' from the rear

Boatman · « **Reply #35 on:** June 23, 2008, 09:20:05 PM »

from the side

Boatman · « **Reply #36 on:** June 23, 2008, 09:20:49 PM »

6-7' from the front

Boatman · « **Reply #37 on:** June 23, 2008, 09:21:34 PM »

45 degree from the front

Boatman · « **Reply #38 on:** June 23, 2008, 09:23:22 PM »

As far as the turnsignals-I stated earlier that they flashed alternate of the stock signals. It is more like a strobe effect when the wing tips are turnsignals-hard to describe but they flash nicely.

Keithincda · « **Reply #39 on:** June 23, 2008, 10:20:13 PM »

Perfect Boatman

...Thanks, I like that look from the rear...thanks for the pictures.

Garznhogs · « **Reply #40 on:** June 24, 2008, 05:19:43 AM »

DITTO! Thanks!

:-Jerry

nidan · « **Reply #41 on:** August 29, 2008, 07:38:54 AM »

I saw those on EGG but glad you can get them direct , the look great!
Low profile , inobtrusive and good light.

Thanks for the pics and write up!

FYI : http://www.biketronics.com/led.html#bt40 for direct

spydglide · « **Reply #42 on:** August 29, 2008, 08:52:09 PM »

Hey Boatman, have you had time to know if while riding at night whether the running lights would be distracting to you? $:-\$ spyder

Boatman · « **Reply #43 on:** October 02, 2008, 02:33:09 PM »

Quote from: spydglide on August 29, 2008, 08:52:09 PM

Hey Boatman, have you had time to know if while riding at night whether the running lights would be distracting to you? $:-\$ spyder

Spyder, Tommy (HD110) asked me the same thing in MV and they are not distracting to me at night. You are a lot more visible (daytime/nightime). I realize they are not for everyone but they work for me.

Boatman · « **Reply #44 on:** October 02, 2008, 02:41:05 PM »

While riding back from MV, I pulled up along side a friend at a stop and noticed about 25% of his LED's were out on the LH side after riding about 1.5 hours in the rain. (07 Ultra)..

He called Biketronics (he ordered direct from them) and received them promptly without having to send his old back first.

But he is sending his replacement set back and waiting on another set. With the replacements, the lights's lack about 3/4" from each end of having NO led's whereas the original set(s) had led's the length of the strip.

Friend called Biketronics back complaining and they said they would make him a set with all LED's as his and mine original sets were/are.

They stated too much bend with all LED's

so they may have had some early failures.

Point is, if you order direct from Biketronics, ask them if you are getting all LED's or are being shorted 3/4" on each end.

bbrown · « **Reply #45 on:** October 02, 2008, 02:48:53 PM »

Wow that really looks good.
Thanks for sharing

bbrown · « **Reply #46 on:** October 02, 2008, 09:59:50 PM »

Quote from: Boatman on June 23, 2008, 09:19:06 PM

6-7' from the rear

In most Midwestern states I do not think these are legal if you can see ANY Yellow from the rear if used as running lights.

If they are just directionals then I think its OK

Anyone know for sure??

bbrown · « **Reply #47 on:** October 02, 2008, 10:04:20 PM »

Quote from: Boatman on June 22, 2008, 06:10:14 PM

Yes the stock front and rear signals still work and the wingtips flash off sequence with the stock turnignals. When the turnsignals are not on, they are running lights.

If they are yellow and used as running lights and can be seen from behind the bike I do not think they are legal in WI and MN

Anyone know for sure??

bbrown · « **Reply #48 on:** October 19, 2008, 09:43:23 PM »

Quote from: bbrown on October 02, 2008, 10:04:20 PM

If they are yellow and used as running lights and can be seen from behind the bike I do not think they are legal in WI and MN

Anyone know for sure??

Anyone know the answer to this?

Boatman · « **Reply #49 on:** October 19, 2008, 10:03:11 PM »

I do not know the answer of this. Some semi trucks or trailers have amber running lights on the rear (aftermarket, not from the factory). Probably not legal, but don't know if they have ever been stopped. I doubt if anyone would be stopped just for this.

I know you asked this several weeks ago and no one answered.
To be honest, I never thought of it being a problem possibly until you mentioned it. As of now, I won't take them off as I think they are a safety factor.
You may try contacting the manufacturer of these and see what they say. www.biketronics.com

I also converted from the rear amber turnsignals to the red turnsignals/brake lights and I believe the light bar is too close together so I am not legal there either possibly.

bbrown · « **Reply #50 on:** October 20, 2008, 12:03:03 PM »

Quote from: Boatman on October 19, 2008, 10:03:11 PM

I do not know the answer of this. Some semi trucks or trailers have amber running lights on the rear (aftermarket, not from the factory). Probably not legal, but don't know if they have ever been stopped. I doubt if anyone would be stopped just for this.
I know you asked this several weeks ago and no one answered.
To be honest, I never thought of it being a problem possibly until you mentioned it. As of now, I won't take them off as I think they are a safety factor.
You may try contacting the manufacturer of these and see what they say. www.biketronics.com
Thanks for your thoughts. I have contacted Biketronics and they have not responded. The Wisconsin State Patrol told me they are not legal as solid Amber is not allowed. I do like the lights and am just finishing installing. Will let you know if I get stopped.

I also converted from the rear amber turnsignals to the red turnsignals/brake lights and I believe the light bar is too close together so I am not legal there either possibly.

timo482 · « **Reply #51 on:** October 21, 2008, 01:32:18 PM »

looking in my handy 2008 commercial truck inspection book......

rear turn - amber or red

backup and license - white

all else in the rear - red [markers, reflectors, id, brake, tail]

timo482 · « **Reply #52 on:** October 21, 2008, 01:36:37 PM »

oops forgot - side marker - amber.

yes i can put a dot sticker on a bike
yes id put one on a bike set up this way - they are not rear lights - they are side markers. side markers can be visible from the rear & often are.
and yes - trucks and truck tractors and trailers often have side marker / turn signals.

MJZ · « **Reply #53 on:** October 27, 2008, 04:17:47 PM »

An update on Biketronics, I ordered a set last week and they promised to get them to me by Wednesday or Thursday by the latest. Today I called to see where they were, I got "sorry, we were waiting on some parts but they are in and we are going to ship today and you should have them by Thursday." I said that was not good enough since it was their problem my fairing was still off due to their mistake, ship them overnight so I can install tomorrow. To which they informed me only if you pay for the overnight shipping. I told them to stick them where the sun don't shine.
I really like them but not enough to put up with that kind of service, so my other choice is Eglide Goodies? I think I'll save the 100 bucks.

amigo Jorge · « **Reply #54 on:** November 15, 2008, 11:32:30 PM »

It was impossible to order this kit directly from Biketronics so I didn't have other option to order from eGlideGoodies....let's see what happen....maybe they learned the lesson

AZSSE · « **Reply #55 on:** November 16, 2008, 11:58:22 AM »

That looks really good - thanks for the info!!

Boatman · « **Reply #56 on:** November 16, 2008, 06:13:29 PM »

Quote from: amigo Jorge on November 15, 2008, 11:32:30 PM

It was impossible to order this kit directly from Biketronics so I didn't have other option to order from eGlideGoodies....let's see what happen....maybe they learned the lesson

Jorge-I ordered them from Eglidegoodies also. Got them fine but took about 3 weeks as Biketronics is slow to deliver product.

I believe you can order from Biketronics, you just have to call to place your order (they are mountain time zone).

amigo Jorge · « **Reply #57 on:** November 16, 2008, 08:15:14 PM »

Quote from: Boatman on November 16, 2008, 06:13:29 PM

Jorge-I ordered them from Eglidegoodies also. Got them fine but took about 3 weeks as Biketronics is slow to deliver product.

I believe you can order from Biketronics, you just have to call to place your order (they are mountain time zone).

Thanks mi amigo. It was easier ordering thru the Internet than calling directly to Biketronics.....They told me twice: I will return your call and they never did so I ordered from the Internet.........let's see

amigo Jorge · « **Reply #58 on:** November 19, 2008, 04:34:06 PM »

Quote from: amigo Jorge on November 16, 2008, 08:15:14 PM

Thanks mi amigo. It was easier ordering thru the Internet than calling directly to Biketronics.....They told me twice: I will return your call and they never did so I ordered from the Internet.........let's see

I got them today.......to my surprise....FAST DELIVERY....Ordered last Friday from eGlideGoodies........and received today Wednesday

Boatman · « **Reply #59 on:** November 19, 2008, 07:53:03 PM »

Great to hear that Eglidegoodies had them in stock and shipped quickly Jorge.

bbrown · « **Reply #60 on:** November 20, 2008, 12:59:22 PM »

Send some photos

amigo Jorge · « **Reply #61 on:** November 21, 2008, 10:30:04 PM »

Quote from: Boatman on November 19, 2008, 07:53:03 PM

Great to hear that Eglidegoodies had them in stock and shipped quickly Jorge.

yeah mi amigo....I couldn't believe it !!

amigo Jorge · « **Reply #62 on:** November 21, 2008, 10:30:37 PM »

Quote from: bbrown on November 20, 2008, 12:59:22 PM

Send some photos

As soon as I install them.....I believe that it will be for T-day....

amigo Jorge · « **Reply #63 on:** November 30, 2008, 10:16:29 AM »

I installed the wingtip fairing lights. The installation was and was not easy. It was because the connectors are there and no problem at all. It was not because the plastic where the LEDs are comes straight and the wingtip fairing is a curve. I had to leave them more than 24 hours with clamps and I had to put some crazy glue at the ends. Also I filled the ends with silicone to avoid the water gets in. Here some pics.

Right side

amigo Jorge · « **Reply #64 on:** November 30, 2008, 10:16:59 AM »

Left side

amigo Jorge · « **Reply #65 on:** November 30, 2008, 10:18:26 AM »

on the right side

amigo Jorge · « **Reply #66 on:** November 30, 2008, 10:18:49 AM »

On the left side

49445CVO · « **Reply #67 on:** November 30, 2008, 01:08:01 PM »

The gap in your fairing..... is it because it is not tightened dow at the time of pics?

amigo Jorge · « **Reply #68 on:** November 30, 2008, 06:19:44 PM »

Quote from: 49445CVO on November 30, 2008, 01:08:01 PM

The gap in your fairing..... is it because it is not tightened dow at the time of pics?

came that way form the factory......

49445CVO · « **Reply #69 on:** December 01, 2008, 12:19:42 AM »

Oh maybe it is the weather stripping that is giving it that look

Cvostu · « **Reply #70 on:** February 08, 2009, 04:03:12 AM »

hey Bob,, i just found this one and once again you did a great job with the install and showing the pics along the way. Too much for me on this one, so I think I'll sit this one out. Cams are next. But I think I'll have John Sachs do that one for me. Great job as usual.

merlin41 · « **Reply #71 on:** February 21, 2009, 01:28:59 PM »

I just received a set of these for my '06 and the limited instructions say that the wires are supposed to come out the bottom of the light on each side. The only way to make the right side mount correctly is to have the wires come out the top. Is this right?

Boatman · « **Reply #72 on:** February 21, 2009, 01:57:21 PM »

Quote from: merlin41 on February 21, 2009, 01:28:59 PM

I just received a set of these for my '06 and the limited instructions say that the wires are supposed to come out the bottom of the light on each side. The only way to make the right side mount correctly is to have the wires come out the top. Is this right?

The wires should come out the bottom of the light (unless they sent you two of the same side). You are mounting them on the edge of the inner fairing?

merlin41 · « **Reply #73 on:** February 21, 2009, 03:17:17 PM »

Thanks. I am mounting them on the inner fairing but it looks like I have 2 indentical light strips. Not mirror images (left and right).

bisounours · « **Reply #74 on:** February 24, 2009, 06:10:15 AM »

Quote from: merlin41 on February 21, 2009, 01:28:59 PM

I just received a set of these for my '06 and the limited instructions say that the wires are supposed to come out the bottom of the light on each side. The only way to make the right side mount correctly is to have the wires come out the top. Is this right?

Good morning merlin41

on the CVO website

It would be nice for the other members if you present you in the thread New member introduction with a pic of your bike

Best regards

Jacques

Author Topic: WingTip Fairing light/turn install with pictures (Read 17805 times)

AZSSE