Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Andrews 48 in a cvo 110  (Read 2979 times)

0 Members and 1 Guest are viewing this topic.

busarealfast

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 122
  • www.CVOHARLEY.com
    • FL

Andrews 48 in a cvo 110
« on: December 30, 2018, 11:14:40 PM »

Anyone have a dyno chart for this cam in a cvo? Cant seem to find one anywhere. Just want a visual of where the torque hits compared to the se255.
Logged
2009 Ultra CVO Stage 4
Vance & Hines Pro pipe
Thundermax auto tune
Ephesians 2:8

HD Street Performance

  • Vendor
  • 2.5K CVO Member
  • *
  • Offline Offline
  • Posts: 3118
Re: Andrews 48 in a cvo 110
« Reply #1 on: December 31, 2018, 10:58:34 AM »

Have not heard of that combination, not that it would not work if torque was your focus. By the numbers it would take a small compression bump to equal the torque down low of the 255 but would be around a little longer after 4500. It is so close to the same I could not see the advantage of going there. If it is just torque you want then use the SE 117 kit and the SE585 cam and a good 2 into one pipe or the Fullsack system. It will peak at over 130 and hit 100 at 2k.
Logged

snowrider13

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 193
Re: Andrews 48 in a cvo 110
« Reply #2 on: January 03, 2019, 08:28:45 AM »

My dyno chart is packed away so no posting. I can tell you that I had a 6-7 HP increase, and a 3 ft# increase in peak torque. This was on a otherwise stock 110 running a Fullsac exhaust, tuned with a Harley super tuner. I choose this cam because I liked the low end grunt of the 255 that needed to be replaced. At no time did the levels of power dip below the 255's, and the 48 pulled out about 200-300 more and "Fell" off less. Bike was tuned by Dave @ Pocono HD.
Logged

snowrider13

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 193
Re: Andrews 48 in a cvo 110
« Reply #3 on: January 03, 2019, 08:32:37 AM »

Final #'s were...99HP/115tq
Logged

busarealfast

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 122
  • www.CVOHARLEY.com
    • FL

Re: Andrews 48 in a cvo 110
« Reply #4 on: January 03, 2019, 06:46:51 PM »

Thanks snowrider!
Logged
2009 Ultra CVO Stage 4
Vance & Hines Pro pipe
Thundermax auto tune
Ephesians 2:8

HD Street Performance

  • Vendor
  • 2.5K CVO Member
  • *
  • Offline Offline
  • Posts: 3118
Re: Andrews 48 in a cvo 110
« Reply #5 on: January 04, 2019, 12:37:38 PM »

I personally used an Andrews 54 in my bike. 105/115 and it hits right off idle, no head work. Pipe is Fulsack DX and recored mufflers 2" baffle. Tuned with tts
« Last Edit: January 04, 2019, 12:47:42 PM by HD Street Performance »
Logged

Dogbone44mag

  • Newbie
  • *
  • Offline Offline
  • Posts: 28
Re: Andrews 48 in a cvo 110
« Reply #6 on: January 05, 2019, 09:13:46 PM »

 Don, who tuned your bike ?
Logged

prodrag1320

  • AMRA & AHDRA P/D record holder
  • Vendor
  • Elite CVO Member
  • *
  • Offline Offline
  • Posts: 917
Re: Andrews 48 in a cvo 110
« Reply #7 on: January 06, 2019, 07:23:42 AM »

theres a whole lot of better cam choices for a 110 besides the 48,look into S&S .570,cycle rama 570,or tman 625.these are all milder cams that will produce power you can feel

HD Street Performance

  • Vendor
  • 2.5K CVO Member
  • *
  • Offline Offline
  • Posts: 3118
Re: Andrews 48 in a cvo 110
« Reply #8 on: January 06, 2019, 08:39:38 AM »

Don, who tuned your bike ?
Easy Street Cycles in Tacoma, Aaron.
Logged

georgw221

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 170
Re: Andrews 48 in a cvo 110
« Reply #9 on: January 06, 2019, 10:20:09 AM »

theres a whole lot of better cam choices for a 110 besides the 48,look into S&S .570,cycle rama 570,or tman 625.these are all milder cams that will produce power you can feel

Here is a Cyclerama 570-2 used as a simple bolt in ,, if your looking for Tq.
Logged

HD Street Performance

  • Vendor
  • 2.5K CVO Member
  • *
  • Offline Offline
  • Posts: 3118
Re: Andrews 48 in a cvo 110
« Reply #10 on: January 06, 2019, 12:46:32 PM »

That is a good result and expected with the good pipe and tune choice
Logged

MCE

  • Guest
Re: Andrews 48 in a cvo 110
« Reply #11 on: January 09, 2019, 10:18:36 AM »

Here is a Cyclerama 570-2 used as a simple bolt in ,, if your looking for Tq.

A little head work (and a larger intake valve) would help that allot.
Logged
 

Page created in 0.351 seconds with 25 queries.