Topic: 2011 FLHXSE2 Saddlebag Speaker Insatall with fairing amp my how too !!!!!!!! (Read 4472 times)

TIF2 · « **Reply #15 on:** April 10, 2012, 06:09:14 PM »

Hey Nick

Good to speak with you today.
I don't think you'll have an issue with the HT bracket and the 6.5" adapters (slight Dremel work aside).

I am slightly concerned with the magnet size of the new speakers and the location of the HT amp.
VERY curious on how your combo pans out.

Please take pics and post up when done, and if I can help along the way, you got the digits brother.

hdnik · « **Reply #16 on:** April 10, 2012, 06:12:15 PM »

Quote from: TIF2 on April 10, 2012, 06:09:14 PM

Hey Nick

Good to speak with you today.
I don't think you'll have an issue with the HT bracket and the 6.5" adapters (slight Dremel work aside).

I am slightly concerned with the magnet size of the new speakers and the location of the HT amp.
VERY curious on how your combo pans out.

Please take pics and post up when done, and if I can help along the way, you got the digits brother.

Will Do Rich. And if there is EVER anything you think I may be able to help YOU with (If that's possible

)... Be sure to let me know! Thanks Man!

Skillet · « **Reply #17 on:** April 10, 2012, 06:12:30 PM »

Thanks for the info. Lots of choices to make on the threads out there.

hdnik · « **Reply #18 on:** April 12, 2012, 12:08:06 AM »

All speakers, harnesses, manuals, and amp are now in my hands.... Just waiting on painted lids from Colorado. Will do my own pictorial install when the games begin.

Thanks again Rich.

Harleypingman · « **Reply #19 on:** April 12, 2012, 02:52:08 PM »

These are the installation instructions for the HD saddlebag speaker kit used in this project:

http://www.harley-davidson.com/en_US/Media/downloads/Service/isheets/-J05386.pdf

You'll notice under the "Installation Requirements" on the first page that it says that a "Radio Harness" or "non-Ultra Overlay harness" are required. These harnesses provide the connection from the kit's audio harness for the rear speakers to the Harman Kardon radio's pin-outs for the rear speakers.

However, since the SESG2/3 already have a connector plugged into the back of the HK (for the iPod module) that would otherwise be used for the Radio or NUOH harnesses referenced in the kit, an alternative way to access the rear speaker pin-outs while also supplying connectors for the rear speakers to the kit's harness is necessary.

What TIF2, Rich, has supplied are the harnesses/parts to retain the OEM plug in the HK radio (by simply adding the 4 wires to connect to the rear speaker pin-outs of the HK radio) as well as the mating connectors for the rear speakers for the kit's harness.

I add this info not to detract from what the OP and Rich have done, but to assist others considering a similar project by providing some additional information.

Nice project and thanks for the pictures.

Carl

TIF2 · « **Reply #20 on:** April 12, 2012, 03:37:23 PM »

Quote from: Harleypingman on April 12, 2012, 02:52:08 PM

What TIF2, Rich, has supplied are the harnesses/parts to retain the OEM plug in the HK radio (by simply adding the 4 wires to connect to the rear speaker pin-outs of the HK radio) as well as the mating connectors for the rear speakers for the kit's harness.

Right you are Carl!!

Harleypingman · « **Reply #21 on:** April 12, 2012, 10:10:03 PM »

And noone supplies better, assembled connectors than Rich!!!

hdnik · « **Reply #22 on:** April 13, 2012, 12:41:45 AM »

Quote from: Harleypingman on April 12, 2012, 10:10:03 PM

And noone supplies better, assembled connectors than Rich!!!

Had a small parts delivery today. Attempted to make my own harness to install the 70.2 amp between NUOH and rear speaker harness.
All was going well as I laid all the harnesses out on the bench... Suffice to say I now know the difference between a "DT" and a "DTM" Deutsch connector.

And the beat goes on. (what a dummy)

benz · « **Reply #23 on:** April 21, 2013, 07:30:37 PM »

Re: 2011 FLHXSE2 Saddlebag Speaker Insatall with fairing amp my how too !!!!!!!!
« Reply #22 on: April 13, 2012, 12:41:45 AM »
Reply with quoteQuote
Quote from: Harleypingman on April 12, 2012, 10:10:03 PM
And noone supplies better, assembled connectors than Rich!!!

Had a small parts delivery today. Attempted to make my own harness to install the 70.2 amp between NUOH and rear speaker harness.
All was going well as I laid all the harnesses out on the bench... Suffice to say I now know the difference between a "DT" and a "DTM" Deutsch connector.

And the beat goes on. (what a dummy)

Can you tell me what the pin location no.s are for the rear speaker out puts? I am trying to wire up my rear speaker pods on my 2011 cvo street glide. Thanks for your help

2015 FLHXSE · « **Reply #24 on:** April 21, 2013, 09:26:47 PM »

Radio: Input side: Output side:

Grey ----- > Yellow --------------- --- > Blue ---- > Grey --------- > Deutsch Connector (Rt Spkr + )

Gry/Blk - > Black --------------- --- > Black -- > Gry/Blk ----- > Deutsch Connector (Rt Spkr - )

Wht ----- > Green --------------- --- > Brown ---- > Wht ----- > Deutsch Connector (Lft Spkr + )

Wht/Blk - > Black --------------- --- > Black ---- > Wht/Blk - > Deutsch Connector (Lft Spkr - )

Author Topic: 2011 FLHXSE2 Saddlebag Speaker Insatall with fairing amp my how too !!!!!!!! (Read 4472 times)