Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Black Diamond]

Used some second gen SERK parts that weren't part of our 02 and 03 bikes to begin with Joe.  Remember that you've done at least the ring.  That ignition switch is nice little addition too.

That's a real nice "touch" on the ring. Is that from the 07 SERK? Ruby needs some love, may need to do this for her.
I really like the old school V-Wing handlebar cover. Nice bit of chrome for that area.

Damn shame on the seat. Not off by much. Since your putting a custom cover on it anyway, see what can be done to add a bit to the nose. You'll figure out a solution.

JW

[Twolanerider]

That's a real nice "touch" on the ring. Is that from the 07 SERK? Ruby needs some love, may need to do this for her.
I really like the old school V-Wing handlebar cover. Nice bit of chrome for that area.

Damn shame on the seat. Not off by much. Since your putting a custom cover on it anyway, see what can be done to add a bit to the nose. You'll figure out a solution.

JW

Those bits at the ignition switch are 07 pieces.  Subtle differences for sure.  But once you've seen them it's easy to decide they belong there. 

If I remember correctly the ring and ignition switch were VIN protected.  So you might need a buddy-assist to get them.

It was an easy choice on the handlebar cover.  The dash sweeps up the tank so the splash of chrome against red is already there.  It continues nicely with the handlebar cover.  Was hoping it would look good there but had that other handlebar cover powder coated while all the parts were in just in case.

[Twolanerider]

Was out in the shop at O-dark-30 this morning clearing my head from another project.  Had the saddlebags completely reassembled last week so decided to hang and adjust them and the front fender.  Took a step back when done and was taken aback a bit.  First time it's ever actually looked like a motorcycle again.  A gutted motorcycle for sure.  But it's at least bike-like now.

I know, some bits will be in the way of later work.  But it'll be worth it for all the test fitting that is done. 

[Twolanerider]

.

[Twolanerider]

.

[Twolanerider]

.

[Twolanerider]

.

[Twolanerider]

.

[Twolanerider]

Seeing these images reminds me that thanks are owed to many here for their interest as I've played here.  In some cases much more than interest.  The saddlebag supports now seen and nearly all the saddlebag hardware were freebies from site members as the parts collection process was ongoing.  Other bits throughout the bike have been contributions or deeply discounted additions to the cause.  It's something of a community project. 

None of you get to ride it though !

[naitram]

get some wheels and tires on and you'll have a nice rolling chassis

[110tHunDer]

Seeing these images reminds me that thanks are owed to many here for their interest as I've played here.  In some cases much more than interest.  The saddlebag supports now seen and nearly all the saddlebag hardware were freebies from site members as the parts collection process was ongoing.  Other bits throughout the bike have been contributions or deeply discounted additions to the cause.  It's something of a community project. 

None of you get to ride it though !

Ha!  I forgot all about those until I read this!

The bike's looking great, Don!

[naitram]

this gonna be ready for MV?

[Twolanerider]

get some wheels and tires on and you'll have a nice rolling chassis

They are sitting in a corner over there >>> .  American Wire 100 spokes with Avon Venoms installed.  Could hang the front but still no engine.  Suppose could hang the swingarm on the pivot shaft just from a place to hang a back tire and make the whole thing roll ?

Actually if that would work without marking up any parts it might not be a bad idea.  Until recently lifting the frame on and off the cart wasn't a big deal.  It's become a two person job now (at least to do it safely).  Will have to study this a bit....

[Twolanerider]

Ha!  I forgot all about those until I read this!

The bike's looking great, Don!

Thanks Brian.  And you've definitely got a hand in this project.  Those supports are perfect.  The Lindby rear crash bars that made those supports a necessity are in a pile over there << .  They'll go on sometime to complete the set with your supports.

All the chrome 12 point hardware is beginning to worry me.  I like it; almost too much.  Keep looking over at the other bikes and thinking.....

[Twolanerider]

this gonna be ready for MV?

Not a chance.  Still have to build an engine.  What I thought would be last winter's winter project will hopefully be this winter's winter project.  Even the few hours this project has taken the last couple months have been most the spare bike/play time.  Have enough time in the project already have no problem with continuing to take it slow.  Only thing that might significantly speed things up would be stumbling in to a good silver take out engine somewhere/some time.  But it's not anything I'm going to worry about at all.