www.CVOHARLEY.com
CVO Technical => Twin Cam => Topic started by: joker1450 on February 26, 2006, 01:18:24 PM
-
I have loose one banjo bolts that tighteen the backplate of AN big sucker to the motor heads >:(
Where can I find another?
I can't belive that I must buy another BIG SUCKER! :-[
thank you
-
Have you tried calling Ness yet to see if you can get a another bolt. Harley sells thier's and I was able to buy and extra from Zippers for their's cant imagine them trying to bone you for a whole setup to get one.
-harry
-
If you mean the newer two-piece mounting studs, I've got some extras in my garage, if you run up against a brick wall getting some let me know.You can also get them through Chicago H-D on line. Should be the same part number for all TWIN CAM models, but am not positive on that one. H-D part no. 29477-99A.
Joe
-
If you mean the newer two-piece mounting studs, I've got some extras in my garage, if you run up against a brick wall getting some let me know.You can also get them through Chicago H-D on line. Should be the same part number for all TWIN CAM models, but am not positive on that one. H-D part no. 29477-99A.
Joe
I can't find on line the item n. 29477-97A, what is this? :'(
-
I'll paste the link to H-D accessories that has a note that references the bolts I believe you're referring to, they're down towards the bottom of the page. Says these are required is current mounting bolts are the one piece version, etc. Hope this doesn't muddy the waters further:
http://www.harley-davidson.com/gma/gma_product.jsp?PRODUCT%3C%3Eprd_id=845524442101569&FOLDER%3C%3Efolder_id=2534374302287057&ASSORTMENT%3C%3East_id=2534374302287057&bmUID=1141028827678&bmLocale=en_US'\
Ciao,
Joe
-
I'll paste the link to H-D accessories that has a note that references the bolts I believe you're referring to, they're down towards the bottom of the page. Says these are required is current mounting bolts are the one piece version, etc. Hope this doesn't muddy the waters further:
http://www.harley-davidson.com/gma/gma_product.jsp?PRODUCT%3C%3Eprd_id=845524442101569&FOLDER%3C%3Efolder_id=2534374302287057&ASSORTMENT%3C%3East_id=2534374302287057&bmUID=1141028827678&bmLocale=en_US'\
Ciao,
Joe
this link doesn't work! [smiley=oops.gif]
-
This is the link, but those are not the hollow bolts that attach the backing plate to the breather ports in the head.
-
This is the link, but those are not the hollow bolts that attach the backing plate to the breather ports in the head. http://www.harley-davidson.com/gma/gma_product.jsp?PRODUCT%3C%3Eprd_id=845524442101569&FOLDER%3C%3Efolder_id=2534374302287057&ASSORTMENT%3C%3East_id=2534374302287057&bmUID=1141028827678&bmLocale=en_US
Joker - I think you will need to contact Ness for a replacement. If I remember correctly, the Ness part is made differently than the Screamin' Eagle part. Contact Ness and have them advise you, they should offer to just send you one, or they can tell you for sure if the H-D part will work.
email: contact@arlenness.com
Jerry
just do it, I'm waiting the reply [smiley=xyxthumbs.gif]
-
Joker,
I just looked up the Big Sucker kit in two catalogs, seems you are looking for one of the smaller drilled bolts for the vent,rather than the mounting studs for the backplate that I thought. My mistake. Seems I did not save the install instructions for this kit, but if you still have it and it has the Ness part number, they should help you get a replacement. If not post the part number here and one of us 'locals can go up and brow beat them a bit, they're about 30 minutes from the house. I still have the stock banjo bolts I removed, but as GRC says they a bit different than stock H-D.
-
Joker,
I just looked up the Big Sucker kit in two catalogs, seems you are looking for one of the smaller drilled bolts for the vent,rather than the mounting studs for the backplate that I thought. My mistake. Seems I did not save the install instructions for this kit, but if you still have it and it has the Ness part number, they should help you get a replacement. If not post the part number here and one of us 'locals can go up and brow beat them a bit, they're about 30 minutes from the house. I still have the stock banjo bolts I removed, but as GRC says they a bit different than stock H-D.
I don't have the instruction sheet. [smiley=oops.gif]
I'm waiting the reply from Arlen Ness... [smiley=nixweiss.gif]
In the AN site, if you "search" banjo comes out many banjo bolts (without picture)! :'(
-
I sent them a request for a reaplacement install sheet, which normally has the parts breakdown. Which part number AN "Sukah" did you use on your ride? I may be able to get up there on Saturday or Sunday, see what I can get as a Plan B.
Ciao,
Joe
-
I sent them a request for a reaplacement install sheet, which normally has the parts breakdown. Which part number AN "Sukah" did you use on your ride? I may be able to get up there on Saturday or Sunday, see what I can get as a Plan B.
Ciao,
Joe
My sucker is the number 18-501
for FLHT 2002 carb
thank You very much!
-
This is the PDF from Ness for the install and also lists the components (if I am actually able to post it...)
Cheers
Dave
-
This is the PDF from Ness for the install and also lists the components (if I am actually able to post it...)
Cheers
Dave
[size=24]I love YOU[/size]
[smiley=banana.gif] [smiley=banana.gif] [smiley=banana.gif]
[smiley=xyxthumbs.gif] [smiley=xyxthumbs.gif] [smiley=xyxthumbs.gif]
-
Hey - Steady there Joker - you will get us "Macho Europeans" a bad name ;)
Glad I could help
Cheers
Dave
-
This site is amazing! I live maybe 30 mins from Arlen Ness and haven't heard back from them for about a week, but manage to get a replacement instruction sheet from the UK while trying to help someone in Italy. H-D globalization in action! I'll see what I can get this weekend from Ness Joker, probably not until Sunday.
[smiley=drink.gif]
Cheers,
Joe
-
This site is amazing! I live maybe 30 mins from Arlen Ness and haven't heard back from them for about a week, but manage to get a replacement instruction sheet from the UK while trying to help someone in Italy. H-D globalization in action! I'll see what I can get this weekend from Ness Joker, probably not until Sunday.
[smiley=drink.gif]
Cheers,
Joe
Thank You Dave, I have found another bolt in a friend's garage.
[smiley=xyxthumbs.gif]
-
I'm just glad I was able to help - sounds corny I know but I am
Cheers
Dave