www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 ... 6 7 [8] 9 10
 71 
 CVO Social / New Member Introduction / Re: Hello
 on: April 15, 2024, 03:32:45 PM 
Started by marcofreeman - Last post by Grizzly
Welcome to wonderful site from Southern Ontario.

 72 
 CVO Social / Pictures / Re: Social Kangaroo's
 on: April 15, 2024, 03:30:40 PM 
Started by Aussie - Last post by Grizzly
Very cool pics.

I guess the message to the cricket players is to "hop to it" and finish the game.  Whaw, whaw, whaw.   :P

 73 
 CVO Technical / Wheels/Tires/Suspension/Brakes / Re: Motor vibration
 on: April 15, 2024, 03:25:00 PM 
Started by longlast - Last post by Twolanerider
Quote from: longlast on April 15, 2024, 11:40:20 AM
                        Sorted out!! ;D

         I tried something I saw on YouTube  by GlidePro Motor Mount Install

     He says to leave the mount fixings lose then go for a ride that will let the motor find it's  place to settle,  then tighten the to side bolts of the mount and the centre one  only snug it up so you can still move it back and forth,  job done.

      That's what I did and the issue is solved it's back too smooth riding.  :2vrolijk_21:


Gawdammit!!  That's what happens when you don't read on through a thread before answering!   :huepfenlol2: :huepfenlol2:

 74 
 CVO Technical / Wheels/Tires/Suspension/Brakes / Re: Motor vibration
 on: April 15, 2024, 03:24:12 PM 
Started by longlast - Last post by Twolanerider
Quote from: longlast on April 14, 2024, 11:45:25 AM
  Any suggestions on motor vibration 07 ultra classic?

New Swingarm stabilisers installed front mount replaced with a Drag Specialties mount .

Q. Should the motor be pulled forward before tightening bolts up?

At idle it's much better bars don't bounce around like they did. But now at 11 / 1200 rpm crazy vibration.  When riding there's vibration felt.

I'm thinking the motor isn't sitting correctly??

Any suggestions I might try or should  do are welcome.   Cheers

Left is Drag Specialties,..right is HD

Leave everything just snug (not tightened at all) and go for a ride.  Then tighten it up.  You'll likely fix your problem  :2vrolijk_21: :2vrolijk_21: .

 75 
 CVO Technical / Electronic Toys and Gadgets / Re: Wifi Access Point Password
 on: April 15, 2024, 11:41:33 AM 
Started by MikeyBfromTN - Last post by Finster101

"Your salesman is an idiot."   8)

Say it ain't so!   :beerchug:

 76 
 CVO Technical / Wheels/Tires/Suspension/Brakes / Re: Motor vibration
 on: April 15, 2024, 11:40:20 AM 
Started by longlast - Last post by longlast

                        Sorted out!! ;D

         I tried something I saw on YouTube  by GlidePro Motor Mount Install

     He says to leave the mount fixings lose then go for a ride that will let the motor find it's  place to settle,  then tighten the to side bolts of the mount and the centre one  only snug it up so you can still move it back and forth,  job done.

      That's what I did and the issue is solved it's back too smooth riding.  :2vrolijk_21:

 77 
 CVO Social / Rider Down / Re: Prayers needed for Jim May/ Chains
 on: April 15, 2024, 10:54:45 AM 
Started by danner55 - Last post by D-N-D
Hang in there Brother !!! Praying for you too have a full recovery !!!!

Dante

 78 
 CVO Social / Rider Down / Re: Prayers needed for Jim May/ Chains
 on: April 15, 2024, 10:34:27 AM 
Started by danner55 - Last post by Twolanerider
I read (online) that Jim's recovery was being done inside a well padded Bushtec trailer.

 79 
 CVO Social / Rider Down / Re: Prayers needed for Jim May/ Chains
 on: April 15, 2024, 07:32:12 AM 
Started by danner55 - Last post by blacktop
Get well soon Jim..

 80 
 CVO Social / Rider Down / Re: Prayers needed for Jim May/ Chains
 on: April 15, 2024, 06:43:56 AM 
Started by danner55 - Last post by Cvostu
Get well soon Jim. Lots of prayers for you. Stuart

Pages: 1 ... 6 7 [8] 9 10

Page created in 0.148 seconds with 18 queries.