www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Monkey bars  (Read 5674 times)

0 Members and 1 Guest are viewing this topic.

toybldr

  • Newbie
  • *
  • Offline Offline
  • Posts: 12
    • ON


    • CVO1: 04 SEEG
Monkey bars
« on: March 29, 2015, 09:39:54 PM »
Yaffe 12 inch monkey bars installation. anyone installed on 04. Any problems?
Logged

SG Racer

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1636

    • CVO1: 2011 SESG2, Black Diamond/ Inferno Orange
    • CVO2: 2005 SEEG, Cherry
Re: Monkey bars
« Reply #1 on: April 16, 2015, 12:29:17 PM »
I have the same bars on my 2011 CVO Streetglide. I have a 2005 CVO Electraglide and I put 13 inch Cyclesmith bars on it. The Yaffe bars I really like, but I waited for ever for them to come in and they never did for the 05. I decided to go ahead with the Cyclesmith bars. I like them also.
 As far as the Yaffe bars go, they can be a pain in the butt to get the wires through. They do a terrible job on the inside of the bars. You will have to replace the front on piece brake line and the line up to the master cylinder. You will have to also replace all the throttle cables.
They say their bars are 12 inch but they are really about 13.
Holler if you need anything else.
Logged
D&D Fat Cat W/Ghost pipe
Custom leather seat
12" Yaffe Monkey Bagger Bars
SEPST
93Hp, 116Tq

sharpshooter

  • Newbie
  • *
  • Offline Offline
  • Posts: 25
  • www.CVOHARLEY.com
    • NC

    • CVO1: 04' SEEG BLACK/BLUE
Re: Monkey bars
« Reply #2 on: May 19, 2015, 08:46:02 AM »
I was looking at LA choppers twin peaks but, it says not for bikes with hydraulic clutches before 2014. Haven't found out why yet
Logged

cvo-05

  • Newbie
  • *
  • Offline Offline
  • Posts: 28
Re: Monkey bars
« Reply #3 on: July 02, 2015, 07:27:43 PM »
I put the LA choppers on mine no problem with mounting the clutch on my 2005 SEEG
Logged
2005 Seeg Big Bird
2005 Deluxe 95 CI Hot Rod

Puzzled

  • Vendor
  • 5k CVO Member
  • *
  • Offline Offline
  • Posts: 8801
    • PA


    • CVO1: 2018 FLTRXSE Road Glide Custom (SOLD)
    • CVO2: 2013 FLTRXSE2 Road Glide Custom (SOLD)
    • CVO3: 2001 FLTRSEI2 Road Glide (SOLD)
Re: Monkey bars
« Reply #4 on: July 02, 2015, 07:43:12 PM »
Quote from: toybldr on March 29, 2015, 09:39:54 PM
Yaffe 12 inch monkey bars installation. anyone installed on 04. Any problems?

If you go with Yaffe bars check the holes and chamfers as I have seen sharp edges that needed some addressing. The bars look great when installed.
Logged
2023 CVO Road Glide
2003 Rigid Springer Chopper "Puzzle" Bike 26"

bogosh717

  • Newbie
  • *
  • Offline Offline
  • Posts: 8
  • www.CVOHARLEY.com
    • MA


    • CVO1: 07 CVO Ultra
Re: Monkey bars
« Reply #5 on: October 12, 2015, 11:50:24 AM »
I have a 2007 Ultra cvo and I was looking to install 10 inch Yaffe monkey bars but some websites say they will not fit. Any help would be great....Thanks in advance.
Logged

sharpshooter

  • Newbie
  • *
  • Offline Offline
  • Posts: 25
  • www.CVOHARLEY.com
    • NC

    • CVO1: 04' SEEG BLACK/BLUE
Re: Monkey bars
« Reply #6 on: October 25, 2015, 10:20:09 AM »
10" Yaffe originals. Had to make the holes bigger for all the wires, got new brake lines from Magnum Shielding and will probably get new throttle cables this winter so they can go back through fairing comfortably
Logged

bogosh717

  • Newbie
  • *
  • Offline Offline
  • Posts: 8
  • www.CVOHARLEY.com
    • MA


    • CVO1: 07 CVO Ultra
Re: Monkey bars
« Reply #7 on: October 25, 2015, 11:14:34 AM »
So there was no problem with the hydraulic clutch fitting ? I heard there might be a clearance issue.
Logged

mattm

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 247
  • FLHRSEI.ORG

    • CVO1: 2005 FLHTCSE2
Re: Monkey bars
« Reply #8 on: October 27, 2015, 10:29:48 PM »
On my 05, I had to use a special version made to work with the hydraulic clutch.  I imagine your 04 will need the same.
Logged

sharpshooter

  • Newbie
  • *
  • Offline Offline
  • Posts: 25
  • www.CVOHARLEY.com
    • NC

    • CVO1: 04' SEEG BLACK/BLUE
Re: Monkey bars
« Reply #9 on: November 01, 2015, 11:14:27 AM »
Quote from: bogosh717 on October 25, 2015, 11:14:34 AM
So there was no problem with the hydraulic clutch fitting ? I heard there might be a clearance issue.
No, the bars are the same diameter as stock with no steps so, no problems.
Logged

bogosh717

  • Newbie
  • *
  • Offline Offline
  • Posts: 8
  • www.CVOHARLEY.com
    • MA


    • CVO1: 07 CVO Ultra
Re: Monkey bars
« Reply #10 on: November 28, 2015, 08:25:10 PM »
Does anyone know I will need to install yaffe 10 monkey bars. Will the clutch line, brake line and throttle cables be long enough ? Also will I need the wire extensions.
Thanks in advance.

Logged

sharpshooter

  • Newbie
  • *
  • Offline Offline
  • Posts: 25
  • www.CVOHARLEY.com
    • NC

    • CVO1: 04' SEEG BLACK/BLUE
Re: Monkey bars
« Reply #11 on: November 29, 2015, 08:33:03 AM »
I had to replace my brake lines on my 04'. For some reason they put shorter ones on the cvo. You can call Maria, at Magnum Shielding
 
Logged

sharpshooter

  • Newbie
  • *
  • Offline Offline
  • Posts: 25
  • www.CVOHARLEY.com
    • NC

    • CVO1: 04' SEEG BLACK/BLUE
Re: Monkey bars
« Reply #12 on: November 29, 2015, 08:34:30 AM »
I had to extend my wires too
Logged

TravRMK

  • Newbie
  • *
  • Offline Offline
  • Posts: 2
  • www.CVOHARLEY.com
    • ID
Re: Monkey bars
« Reply #13 on: January 26, 2016, 04:49:37 PM »
Is the hydraulic clutch line the same for all Harley hydraulic clutches?  I need to find an extended line for my 13" bars.
Logged
 

Page created in 0.285 seconds with 22 queries.