Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[gabe]

 hi got my bike back yesterday and loving the new motor already put 150 miles on it
 the question i have is  what rpm can i run her up to ?
i have a 251 cam  all else is stock 110
its hard to believe how she runs loving it
thanks Gabe
 PS all  uploads to computer have been done for 110

[Fired00d]

I think the MoCo recommending break-in is for all models/motors. Check your owners manual and follow those directions for RPM/Mileage and you should be good to go.

 
Ride Safe,
Fired00d
 

[skreminegul07]

hi got my bike back yesterday and loving the new motor already put 150 miles on it
 the question i have is  what rpm can i run her up to ?
i have a 255 cam  all else is stock 110
its hard to believe how she runs loving it
thanks Gabe
 PS all  uploads to computer have been done for 110

the 110 motor comes with the SE-255 cam stock.

[Rooster]

Even with headwork and SERT and 50mm tb I run out of power about 4500 rpm with the stock 255's

[gabe]

 sorry about that put the 251 cam
thanks gabe

[aka_Matt]

so it has the 251 cam? r u sure it has the right computer program in it? the only 2 programs for a 110 r stock, (stock pistons/255 cam), and the race kit, with the 10.5 pistons/260 cam... they have a program for the 251 cam/stock heads for the 103" motor, not the 110"... on another note, u should have the heads done (shaved) to raise the compression up to about 10.1 with that big(ger) cam, as that cam with 9.1 compression will be very soft under 3k rpms...

[Rooster]

My first build was domed pistons,251 cams, 50mm tb, sert, Baisley pro street heads. No low end pinged real bad, even off stop light when temps were 85-95. Oil temps 280-305. Only ran good 85 mph on up. Comp 10.5-1. Took out the pistons, replaced with forged flat tops. Back to 255 cams, dropped comp to 9.6-1 ran much better with 100 ft lbs of torque at 1800rpm, and retuned. Ran much better and cooler. Only thing is the head gaskets keep blowin.

[OILCAN1]

Ran much cooler with 255 cams, I find this hard to believe.

[tennisman]

Gabe:  follow the owner manual instructions. I personally have rarely gone passed 3000 RPM even now after 10 months old (got 14k miles now).  After all, it IS a touring bike.

[gabe]

 but it is so much fun to run it  hard  but even just riding a round is more fun  i really love it i do not think i could own another bike with out  its there when you want it   loveing it can not what to take a trip with it

[Spikesmith01]

I have a CVO Fat Bob with the 110. I put 251 cams in, SERT, and rush slip ons.
Got it in the winter and had all the work done before i got it.
It slugs a little at take off, but pulls hard from 2200 all the way to 6200. I love the bike. It was pretty much broke in on the dyno. I babied it for the first 1000 miles most of the time. The biggest thing is just make sure its all warmed up before you run it hard. That dosent seem to be a problem withe this bike as it runs too hot. I mean just run it for a few good miles before you rev it up high.
The engine does seem to run hot and the heat management system will kick the rear cylinder off. This just happened as I got off the highway and into some redlights. It was 80 degrees out, but i wasn't running it hard in traffic. I will see what the dealer reccomends.

[gabe]

 THANKS GABE

[ckraus]

Hi,

I have the exact same setup.. What map did you use?

Thanks
Chris.

[gabe]

 the dealer setup up before giving it back  just installed a set of  v&h power duals  love them also
thanks Gabe

[Rooster]

Ran much cooler with 255 cams, I find this hard to believe.

I think it ran much cooler with a much better tune.

[Rooster]

Ran much cooler with 255 cams, I find this hard to believe.

I believe it runs cooler because of the drop in compression and a better tune. The 255's are hard to beat for low to midrange but not good over 4-4500 rpm's