www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: SESRT ACR Question  (Read 867 times)

0 Members and 1 Guest are viewing this topic.

09 S/T FLTRSE3

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 95

    • CVO1: 2009 Silver/ Titanium FLTRSE3
SESRT ACR Question
« on: November 16, 2009, 07:06:49 PM »
Hey All,

This may have been asked and answered previously. If so I can't find the thread. I downloaded the correct baseline map from the SESRT to my 09 FLTRSE3. After doing so it seems like maybe the ACRs are not working. The bike strains to start, and pops back through the throttle body once in a while. I seem to recall a discussion regarding the ACRs being turned off by downloading a different map. Does anyone know how I can check to see if this is the case, and how to turn them back on if so.

Thanks in advance, Ken  8)
Logged

miker

  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 8710

    • CVO1: 2009FLHTCUSE4
Re: SESRT ACR Question
« Reply #1 on: November 16, 2009, 07:26:48 PM »
Yup, some versions in some maps have the acr defalut setting as off...nice huh?

Go to the Tuning Setup, at the bottom of the list in tuning constants, you'll see the tabs.  Click acr and insure the enabled dot is filled in.
Logged

Heatwave

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1429
  • ‘10 CVO Ultra 120/127 & ‘17 CVO LTD 140/151

    • CVO1: 2017 CVO Limited (Garnet/Red) 128ci
    • CVO2: 2010 SE Ultra (Red/Slate)
Re: SESRT ACR Question
« Reply #2 on: November 16, 2009, 07:33:13 PM »
Quote from: miker on November 16, 2009, 07:26:48 PM
Yup, some versions in some maps have the acr defalut setting as off...nice huh?

Go to the Tuning Setup, at the bottom of the list in tuning constants, you'll see the tabs.  Click acr and insure the enabled dot is filled in.

It may be obvious but don't forget to save the map after you enable the ACRs and then you'll need to download the new saved map back to the bike.
Logged

aclass

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 780

    • CVO1: FLTRSE3
Re: SESRT ACR Question
« Reply #3 on: November 16, 2009, 08:32:43 PM »
Quote from: miker on November 16, 2009, 07:26:48 PM
Yup, some versions in some maps have the acr defalut setting as off...nice huh?

Go to the Tuning Setup, at the bottom of the list in tuning constants, you'll see the tabs.  Click acr and insure the enabled dot is filled in.

miker is on the money!   Default is disabled probably due to the 110's only having the ACR's.
Logged

miker

  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 8710

    • CVO1: 2009FLHTCUSE4
Re: SESRT ACR Question
« Reply #4 on: November 16, 2009, 08:39:36 PM »
I havent found the "quit burnin my leg " dot..... ;) :drink:
Logged

HOGMIKE

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2354
  • 65 FLH 93" + others
Re: SESRT ACR Question
« Reply #5 on: November 16, 2009, 08:43:19 PM »
Quote from: aclass on November 16, 2009, 08:32:43 PM
miker is on the money!   Default is disabled probably due to the 110's only having the ACR's.

AND the cop bikes, and Trikes, and the Limited.........FYI

Can't really figure out why some bikes have that disabled, along with the EITMS function.........go figure, dealer takes care of that, though.
Logged
HOGMIKE

HOGMIKE

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2354
  • 65 FLH 93" + others
Re: SESRT ACR Question
« Reply #6 on: November 16, 2009, 08:44:50 PM »
Quote from: miker on November 16, 2009, 08:39:36 PM
I havent found the "quit burnin my leg " dot..... ;) :drink:

I remember an ad somewhere (maybe Harley?) about some Kevlar jeans.......maybe THAT is what they should sell along with the new bikes?
Logged
HOGMIKE
 

Page created in 0.125 seconds with 22 queries.