Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1] 2 3 ... 19

Author Topic: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS (parts list and instructions)  (Read 100218 times)

0 Members and 1 Guest are viewing this topic.

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS

You will  need 69911-11 and 70933-10 and pages 1thru 3 posted below.TOOLS NEEDED  1)SMALL NEEDLENOSE PLYERS,2)REALLY SMALL DRILL ,PAPERCLIP OR JEWELERS SCREW DRIVER,3) BLACK TAPE ,4) WIRE TIES                                              1)YOU NEED TO TAKE SEAT OFF AND TOUPACK LINER OUT.                                                           2)NEXT UNPLUG TAIL LIGHT PLUG AT REAR OF TOURPAC.  (SHOULD BE 7 WIRES BLACK,VIOLET,AND BLUE.) THIS IS PLUG YOU HAVE TO REALIGN WIRES IN.                     3) DISASSEMBLE TAILIGHT PLUG  ,USE SMALL NEEDLE NOSE TO CLICK PULL WHITE CENTER OUT IN TAILIGHT PLUG ,IT JUST COMES OUT A LITTLE TO UNLOCK .  THEN USE A SMALL ROUND TOOL(PAPER CLIP,JEWELER SCREWDRIVER,OR DRILL) TO PUSH IN ROUND HOLE IN PLUG TO RELEASE THE WIRE, DO TO ALL THE WIRES IN THE PLUG.       4) WHEN WIRES ARE OUT OF THE PLUG YOU NEED TO TEST AND MARK  LEFT , RIGHT,AND MIDDLE SO YOU CAN REALIGN BACK IN PLUG .HARLEY PAGE 2-5  I COPIED AND MARKED #1  THE PICTURE OF PLUG IS FROM REAR. (WIRES  SHOULD SNAP  BACK IN)                                                                                                                                                              5)   FEED MODULE WIRES THRU  TOUR PAK   (I TAPED MINE TO FEED OUT OF LEFT SIDE SO I COULD PUT MODULE IN BUMP OF LINER)                                                                               6 )TAKE Y HARNESS AND PART LOOSE  PLUG ON IT AND  MATCH WIRE COLORS TO EACH OTHER (except yellow to red,white to blue or no wire) ,WIRES SHOULD CLICK IN  DO NOT FORCE.                                                         7 ) INSTALL Y HARNESS AND POSISION WIRING  TO  TOURPAK AND IN TOURPAK  AND PLUG TAILIGHTS IN. YOU MIGHT HAVE TO USE LINER TO FIND RIGHT SPOT FOR MODULE,                                                                                                                                                   8)WIRE TIE AND TEST  GOOD LUCK JDO
« Last Edit: October 12, 2011, 05:07:54 PM by JDOFLHRIDER »
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED
« Reply #1 on: August 13, 2010, 08:50:46 PM »

second 2010 kit pg
« Last Edit: February 06, 2011, 09:41:20 AM by JDOFLHRIDER »
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED
« Reply #2 on: August 13, 2010, 08:51:45 PM »

third pg
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #3 on: August 13, 2010, 08:53:01 PM »

FOURTH PG
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #4 on: August 13, 2010, 08:53:48 PM »

FIFTH PG
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #5 on: August 13, 2010, 08:57:19 PM »

2011 KIT PG 1
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #6 on: August 13, 2010, 08:58:16 PM »

2011 PG 2
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #7 on: August 13, 2010, 08:59:13 PM »

2011 PG 3
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #8 on: August 13, 2010, 09:00:00 PM »

2011 PG 4
« Last Edit: February 09, 2011, 06:40:41 PM by JDOFLHRIDER »
Logged

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #9 on: August 13, 2010, 09:02:13 PM »

2011 PG 5     Last page of both 2010 and 2011 kits part 69911-11 looks the part that makes turn signals on our 2010 seuc's
Logged

bikerboy53

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 237
  • FLHRSEI.ORG
    • OR


    • CVO1: Razor Red '07 FLHRSE3
    • CVO2: Red & Slate '10 FLHTCUSE5
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #10 on: August 17, 2010, 03:26:48 PM »

Has anybody tried to get the harness yet? I have a crimper that allows me to make my own "factory style" wiring -maybe this is something we could figure out and make on our own? Or is the feed harness from the bike different too?

I've looked at the similar "magic converter" product from customdynamics, and I think they require the installation of a run/turn/brake conversion module to make their harness work. I wonder if something like that is needed here for the 2010s too? I don't know enough about the new '11 SEUC lights/turn signals to make any guesses yet... The customdynamics part is at:

http://www.customdynamics.com/hd_tour_pak_led_lighting.htm#Magic™_Converter_for_Harley_Davidson®_Tour_Pak®_

It would be nice to make the T-Pak side lights into run/turn lights too. It looks like the customdynamics harness allows that function.
 8)
Logged
S&S T124
HPI 55mm Throttle Body w/5.3 injectors
VP-016-340 Centrifugal Clutch kit
S&S PowerTune Duals w/Rinehart Touring Mufflers
Garmin Zumo 660
Bushtec Trailer

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #11 on: August 17, 2010, 05:56:10 PM »

part doesn't show up yet,I was gonna match a 2010 and 2011 parts book to see if same part. disclaimer on above part (previous reply) says won't work on S E led tourpak lights.I know leds are harder to work with.
Logged

bikerboy53

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 237
  • FLHRSEI.ORG
    • OR


    • CVO1: Razor Red '07 FLHRSE3
    • CVO2: Red & Slate '10 FLHTCUSE5
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #12 on: August 17, 2010, 10:24:13 PM »

Thanks for the info -looks like I missed the (not so) fine print on the customdynamics website!  :( And TIA for any additional information you can come up with for the HD approach.

I never understood to begin with why HD didn't come out with run/turn/brake on the two LED lights next to the center brake light. I guess this way they get to sell us more stuff!  ???
Logged
S&S T124
HPI 55mm Throttle Body w/5.3 injectors
VP-016-340 Centrifugal Clutch kit
S&S PowerTune Duals w/Rinehart Touring Mufflers
Garmin Zumo 660
Bushtec Trailer

Opossum

  • Blue is Faster
  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 406
  • “Some may never live, but the crazy never die.”
    • TX


    • CVO1: 2014 CVO Ultra Limited Jupiter Blue and Wicked Sapphire
    • CVO2: 2010 FLHTCUSE5 Burnt Amber/Hot Citrus (gone but not forgotten)
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #13 on: August 18, 2010, 01:18:51 PM »

I had the shop install the run/brake/turn module on my scooter and the shop pigtailed two wires to the tour pack lights and they now blink w/the turn signals.  not so bright in the day but great at night.  I think it's just run two wires and done.  They charged me 1/2 hour labor so for me no brainer.
Logged
"And those who were seen dancing were thought to be insane by those who could not hear the music"

JDOFLHRIDER

  • Vendor
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1125
  • 2010 FLHTCUSE5 BURNT AMBER -HOT CITRUS
Re: ADDING TURN SIGNALS TO LED TOURPACK LIGHTS
« Reply #14 on: August 18, 2010, 08:45:55 PM »

i talked to a guy that uses a micro proccessor to work leds flashing ,I'm wonder if harley hardwires or uses a micro processor.when i get more info i'll update.
Logged
Pages: [1] 2 3 ... 19
 

Page created in 0.148 seconds with 22 queries.