Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[hdnik]

We just moved to a new home and had new garage door openers installed. Of course I took my HD garage opener receiver with me from the old house. (it worked mint!!) The installer installed the HD reciever during the install of the new LiftMaster (chamberlain) Elite series opener... no probs plug in and 2 wires...done!

When I brought the SESG to it's new home, I flicked the high beam and presto-openo... no probs. The next day out... it didn't work. I checked the connections and fiddled with them and tried it once it worked... then did not again.

i though it was a connection issue...the HD wires are very fine... so I soldered them to the to little wires that they connect with and then tried again... it worked once... then not again.

I checked that the reciever was working (ie it gets signal and flashes but does not open or close opener). I read the manual troubleshooting and it says that with some openers the HD receiver has to be away from the opener or the signals clash... so I cut my soldered connections and move it to another plug at the from of the garage... (thank goodness HD gives you lots of wire) and connected the ends to the wall mouted control box. Tried again... worked once then nothing.

I re-set the HD reciever... as a last ditch and moved it back up to the ceiling.... again one open and then nothing.

Because the bike is parked right below the reciever I can see and hear it working everytime i flick the highbeams, but the opener will not work. I just noticed that the lights on the opener come on (they come one when you open the door, but its as if the signal from the HD box is not long enough to kick the opener into operation. I also noticed that the wall mounted control panel which has an LED display for time and tempurature (like that matters) dims when I flick the Bike's HB switch... so I know there is a signal going to the opener... it's just not doing anything.

has anyone else had issues with a new chamberlain Elite opener??? Did you find a fix?

[9 1/2 Beers]

 Change the wall mount control panel, Mine was digital for the time and temp also.   it turned out to be the problem

 I bought a cheap single button hard wire control and it worked everytime

 Give it a shot  

 Marty

[grc]

Change the wall mount control panel, Mine was digital for the time and temp also.   it turned out to be the problem

 I bought a cheap single button hard wire control and it worked everytime

 Give it a shot  

 Marty

Either that, or just wire it directly to the opener, not to the wall switch.  The installation directions give you both options.


Jerry

[hdnik]

Either that, or just wire it directly to the opener, not to the wall switch.  The installation directions give you both options.


Jerry

I thought the wall mount might be the issue. It's wired to the opener now... either way it does the same thing. Will try this week when stores open again.

which makes me wonder. There is only 2 wires to the opener from the wall mount. the motion detector on the mount must use those wires to turn on the light but not open the door. So the wall box must have a variable voltage being sent... one for the motion light and one from the button to open the door...so my HD unit wil also turn on the light but not open the door. where am i going here?

why if the HD box is wired to the opener itself does it not bypass the wall switch? Of course the wall switch gets powered by the opener... i know this becasue when you disconectt the 2 wires at  the ceiling the wall mount goes dark and the clock has to be reset.

oh yes and these openers have a battery in them in case the power does go out...

i dunno too much technology to open frigging doors.

[Coyote.]

If the light comes on but the door doesn't open it's not seeing a long enough pulse. Still, I'd disconnect the wall unit and just have the HD unit connected to the opener and see what it does. The HD unit is probably having troubles pulling a good enough short across the wall unit.

[9 1/2 Beers]

 I had the same problem, stumped me for months, I found a pic of what i am talking about for an example, it can be as easy as picking up one of these at a hardware store, give it a shot.

 http://www.amazon.com/Universal-Lighted-Wall-Mounted-Button/dp/B000SRVB76/ref=sr_1_3?s=hardware&ie=UTF8&qid=1315186625&sr=1-3


 It's worth a try, It fixed mine, I had the digital wall mount and replaced it with this simple button kind.

 Let me know if it helps you  

 Marty

[hdnik]

If the light comes on but the door doesn't open it's not seeing a long enough pulse. Still, I'd disconnect the wall unit and just have the HD unit connected to the opener and see what it does. The HD unit is probably having troubles pulling a good enough short across the wall unit.

GREAT IDEA... I WILL TEST THAT NOW!

[hdnik]

I had the same problem, stumped me for months, I found a pic of what i am talking about for an example, it can be as easy as picking up one of these at a hardware store, give it a shot.

 http://www.amazon.com/Universal-Lighted-Wall-Mounted-Button/dp/B000SRVB76/ref=sr_1_3?s=hardware&ie=UTF8&qid=1315186625&sr=1-3


 It's worth a try, It fixed mine, I had the digital wall mount and replaced it with this simple button kind.

 Let me know if it helps you  


 Marty

Marty Thank you,

CoyoteK's test was a success, and you are spot on!  I just took the wall mount out of the loop and flicked my high beams....worked 100% of the time... up, down, midway perfect. Geez that was buggn me! Thanks guys!

So the lesson here is if you get a new garage door opener with a fancy schmansy wall control box... ditch it for the old fashion one. I bet it has to do with the circuit board inside that limits the short to turn on the light with the motion sensor.

Learned something today. I be checking to see in Hardware Store is open on Labour day.

[9 1/2 Beers]

 Glad I could help 

 I love this site

 Marty

[49445CVO]

Ok same problem here but on a comercial door lift.  It has the three buttons on the wall UP/ STOP/ DOWN.  My opener is not connected to the wall buttons it is connected to the lift motor its self.  When I talked to the installer he said I needed an extra part to allow for this unit to be hooked up.  I spent the extra 75-100 and had them install it once the part came in.  It worked for a week or so but then stopped working.  Same thing as stated above.  I hear the H-D receiver click and flash but no movement on the door.  I called them back and they ran some test and the H-D wire to the lift motor works just fine. He showed me as he arked the two wires and the door lifted.  So I ordered another receiver from a member and put it all together and yet the same thing.....NOTHING! I'm really at a loss here.  I see the red light flash, hear the click but no movement.


Any help would be great.


Topper

[tweeter13]

I have mine hooked to the wall switch.  The says open, close and stop.  I just wish I could close the door when I was leaving instead of getting off the bike.   Been working for two years that way. 

[49445CVO]

I have mine hooked to the wall switch.  The says open, close and stop.  I just wish I could close the door when I was leaving instead of getting off the bike.   Been working for two years that way. 

So it opens but wont close?

[Fireguy]

I have the "fancy" opener and was able to make mine work. Now I have the best of both worlds. 

[TinSpinner]

My GDO works when I am in the garage and will close the door after I back out but will not open it when the garage door is closed. I assume the signal from the Tx is too weak to travel through the door. I'm going to try and relocate the receiver tomorrow but I thought it was in an ideal location high up in the garage. May be too close to the opener, read that could cause some problems. Have been carrying a remote in my jacket pocket with my old bike and it worked every time, was hoping the HD system would work so I wouldn't have to carry it around any longer.

[hdnik]

What type of wall button are you using. Fancy one with motion for light and thermometer or just the basic two wire deal.



Sent from my iPad using Tapatalk