www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: FXDWG3:  (Read 4376 times)

0 Members and 1 Guest are viewing this topic.

WG3

  • Newbie
  • *
  • Offline Offline
  • Posts: 17
  • FXDWG3:  located in beautiful downtown Kearney, NE
FXDWG3:
« on: October 09, 2005, 12:48:49 PM »
Is it possible to mount a Harley mini tach on a Wide Glide 3?
« Last Edit: October 09, 2005, 12:49:44 PM by Subpar »
Logged

WG3

  • Newbie
  • *
  • Offline Offline
  • Posts: 17
  • FXDWG3:  located in beautiful downtown Kearney, NE
Re: FXDWG3:
« Reply #1 on: October 10, 2005, 01:01:07 PM »
Anyone?  Will it interfere with the headlamp shroud?  
Logged

nidan

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1416
  • Keep the breeze between your knees

    • CVO1: 02 FWDWG3 Stage IV 95 -sold
Re: FXDWG3:
« Reply #2 on: October 11, 2005, 11:42:52 AM »
Without a bar change , it would , unless you'd consider a dakota digital oval one.
Logged
CVO -'02 FWDWG3 Stage IV 95 -sold
'07 FLHX Stage II 103 95hp/111lbs ft
'09 FJR 1300- 145hp /99 lbs ft
2011 Mustang GT 412hp/390 lbs ft

WG3

  • Newbie
  • *
  • Offline Offline
  • Posts: 17
  • FXDWG3:  located in beautiful downtown Kearney, NE
Re: FXDWG3:
« Reply #3 on: October 12, 2005, 06:28:20 PM »
Nidan,
Logged

nidan

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1416
  • Keep the breeze between your knees

    • CVO1: 02 FWDWG3 Stage IV 95 -sold
Re: FXDWG3:
« Reply #4 on: October 13, 2005, 10:20:44 AM »
You might try the Bombay handlebar with integrated Tach housing PN 55835-05A $339 , the side view in the catalog shows it sets back aways, and may clear OK
« Last Edit: October 13, 2005, 10:22:24 AM by nidan »
Logged
CVO -'02 FWDWG3 Stage IV 95 -sold
'07 FLHX Stage II 103 95hp/111lbs ft
'09 FJR 1300- 145hp /99 lbs ft
2011 Mustang GT 412hp/390 lbs ft

KLars1

  • Newbie
  • *
  • Offline Offline
  • Posts: 19
Re: FXDWG3:
« Reply #5 on: December 17, 2005, 03:40:30 AM »
I checked out the Bombay handlebar and I am pretty sure the tach housing will run into the shroud.  However, I have one so I am going to mount it just to check it out.  My current thinking is I would like to have the option to run the shroud and I want a tach too.

Check out the 2006 P&A book on Pg. 645 item F (For some reason it doesn't come up on the H-D website 69277-05)...I was thinking it *might* work if you remove the FXDWG3 chrome trim underneath the shroud.  I think this is the same mount that comes on the 2006 SE Fat Boy.  If your dealer has one of those, you might be able to measure to be sure.  Pretty expensive at $250 and that is just the top clamp.  You still need the housing and tach.  Notice that the part of the tach mount is machined into the top clamp to save space.  If it works, it would be an awfully "clean" solution.  Either way, I think you are going to lose your chrome trim piece though...

If you try it, make sure to post back with pics.  I'll do the same with my investigation with the Bombay.

Kevin
Logged

CVO WG3

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • FLHRSEI.ORG
Re: FXDWG3:
« Reply #6 on: December 17, 2005, 09:05:40 AM »
Apparently the combination speedo/tach - PN 74462-03A - fits.  There's a FXDWG2 on eBay right now with that unit installed in the WG2/3 console.  I tried to post a picture, but seem to be attachment challenged this morning.  
Logged

KLars1

  • Newbie
  • *
  • Offline Offline
  • Posts: 19
Re: FXDWG3:
« Reply #7 on: December 17, 2005, 11:42:43 AM »
Quote
Apparently the combination speedo/tach - PN 74462-03A - fits.
Logged

CH

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
  • FLHRSEI.ORG
Re: FXDWG3:
« Reply #8 on: September 09, 2006, 10:43:54 AM »
Logged
 

Page created in 0.129 seconds with 24 queries.