Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Power vision code question Ecm:p1 intermittent rear efi  (Read 903 times)

0 Members and 1 Guest are viewing this topic.

jagonza1

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 134
Power vision code question Ecm:p1 intermittent rear efi
« on: December 15, 2018, 07:06:14 PM »

I have a 2003 Road glide fuel injected. I have a 103 long block  with se 257 cams thundermax 50mm throttle body S&S power-tune duels. I installed a power vision  with auto tune pro because my dealer couldn't get the motor to smooth out between 1800 and 2500 rpm and right at 3000 rpm's.

So I started tuning runs yesterday and have already seen improvements. I did two runs yesterday and three today.  The dealer left me with a gas mileage of 29 mpg and after running the power-vision it runs much smoother and I already have seen MPG move up to 37.

But today engine light came on. the power vision read the code Ecm:p1 intermittent rear efi.

Does anyone know what it means? I appreciative any input you may have.
Thank you
John A. Gonzales
« Last Edit: December 15, 2018, 09:20:32 PM by jagonza1 »
Logged

Unbalanced

  • FUD Examiner
  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 6708

    • CVO1: 2011 SESG,
    • CVO2: 2004 SEEG Pumpkin,
    • CVO3: 2002 Police Roadking, Maudie and Maybelle Slayer
Re: Power vision code question Ecm:p1 intermittent rear efi
« Reply #1 on: December 15, 2018, 08:08:32 PM »

Are there any errors in the speedo?
Logged
HBRR Florida Chapter,  STILL - The Fastest Chapter - Proven yet again Bikeweek 2017

jagonza1

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 134
Re: Power vision code question Ecm:p1 intermittent rear efi
« Reply #2 on: December 15, 2018, 08:31:32 PM »

On 03 models it give jiberish. Early models it just Lets you know there is an error but not what it is. You have to use a code reader or the one built into the powervision.  I cleared the code but it did say it tripped 4 times
Thanks
John A. Gonzales
« Last Edit: December 15, 2018, 09:07:40 PM by jagonza1 »
Logged

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: Power vision code question Ecm:p1 intermittent rear efi
« Reply #3 on: December 16, 2018, 09:43:46 AM »


Hard to read the complete code in that photo, but I'm guessing it is P1358.  It involves the secondary circuit of the ignition coil for the rear cylinder being intermittent.  That could mean you have a misfire on that cylinder, or it could just mean you have an intermittent loss of continuity in the circuit.  Question #1:  Are you running stock plugs and wires, or aftermarket?  If aftermarket, the circuit resistance could be affected enough to cause a false code (assuming the engine really isn't misfiring), so you may want to try changing back to stock parts.  If stock, check the plug wire connections at both ends.  Something as simple as a loose or corroded connection can trigger these codes. You can also measure the actual resistance of the plug wires and compare to factory specs.  I don't have a 2003 manual, but for reference the spec for my 2005 is 4975 - 11960 ohms for a 20 inch long plug wire.

Jerry
Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

jagonza1

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 134
Re: Power vision code question Ecm:p1 intermittent rear efi
« Reply #4 on: December 16, 2018, 11:13:46 AM »

Answer I AM RUNNING STOCK PLUGS  AND WIRES AND EVERYTHING IS PLUGGED IN TIGHTLY. ITS HARD TO GET UNDER THER TO CHEC RESISTANCE ON THE WIERE Harley did make that hard to access.. I did consider the plugs and wires but I also wonder about the inj can or and wiring.
Thanks
John A. Gonzales
Logged

Twolanerider

  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 50536
  • EBCM #1.5 Emeritus DSP # ? Critter Gawker #?
    • MO


    • CVO1: 2000 Triple Red Screamin' Eagle Road Glide
    • CVO2: 2002 Candy Brandywine Screamin' Eagle Road King
    • CVO3: 1999 Arresting Red FXR2
Re: Power vision code question Ecm:p1 intermittent rear efi
« Reply #5 on: December 16, 2018, 12:02:37 PM »

15 year old bike with work done sometime later.  How old are the wires?  Age and the heat cycles and environmentals impact wires even if they don't get a lot of miles.
Logged

jagonza1

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 134
Re: Power vision code question Ecm:p1 intermittent rear efi
« Reply #6 on: December 16, 2018, 12:54:59 PM »

Wires are about 5 years old. I tried sumax the dealer put stock one back on and said these won't cause cos issues
Logged

Unbalanced

  • FUD Examiner
  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 6708

    • CVO1: 2011 SESG,
    • CVO2: 2004 SEEG Pumpkin,
    • CVO3: 2002 Police Roadking, Maudie and Maybelle Slayer
Re: Power vision code question Ecm:p1 intermittent rear efi
« Reply #7 on: December 16, 2018, 04:29:27 PM »

Cheapest first -

Plugs, then wires, then coil   
Logged
HBRR Florida Chapter,  STILL - The Fastest Chapter - Proven yet again Bikeweek 2017
 

Page created in 0.162 seconds with 24 queries.