Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: PO118 Engine Temp code  (Read 1119 times)

0 Members and 1 Guest are viewing this topic.

AZSERK

  • Newbie
  • *
  • Offline Offline
  • Posts: 14
  • www.CVOHARLEY.com
    • AZ

PO118 Engine Temp code
« on: February 07, 2020, 10:47:13 AM »

My new to me 03 FLHRSEI2 is showing the ET sensor code (check engine light) the HD box identified it as the PO118 ET code.
Has anyone had their switch itself fail?
I've checked the connection, followed the wires all the way to the loom and found nothing pinched, rubbed, or damaged.
The symptoms are as follows; appears to be running rich, stalling when idling, the idle is roaming all over the place, and takes several cranks to start it (sometimes).
It has a new battery, plugs, plug wires, PCIII that was mapped with the correct map (by their company).
Bike runs good, is not making any pinging noises or signs that its running too hot.
Is it possible the sensor is just going bad after 17 years?
I've got a new sensor on order.  Just looking for advice on what else to check.
Thanks all
Logged

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: PO118 Engine Temp code
« Reply #1 on: February 07, 2020, 11:45:33 AM »


Do a continuity / resistance test of the wiring from the sensor connector to the ECM connector, to verify the wiring integrity.  Any time you have a tuning device like a PCIII inserted into the system, you need to verify the problem isn't in the PCIII wiring.  If the wiring is good, a failed ETS is a very good possibility.  They fail, just like many other sensors.

Jerry

Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

Unbalanced

  • FUD Examiner
  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 6708

    • CVO1: 2011 SESG,
    • CVO2: 2004 SEEG Pumpkin,
    • CVO3: 2002 Police Roadking, Maudie and Maybelle Slayer
Re: PO118 Engine Temp code
« Reply #2 on: February 07, 2020, 12:49:40 PM »

Could remove the PC III and see how bike starts

Might also check/ clean the IAC and possibly the Map sensor

Stalling - might also look for an intake leak

Not sure the ET sensor would affect motor on cold start
Logged
HBRR Florida Chapter,  STILL - The Fastest Chapter - Proven yet again Bikeweek 2017

Twolanerider

  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 50536
  • EBCM #1.5 Emeritus DSP # ? Critter Gawker #?
    • MO


    • CVO1: 2000 Triple Red Screamin' Eagle Road Glide
    • CVO2: 2002 Candy Brandywine Screamin' Eagle Road King
    • CVO3: 1999 Arresting Red FXR2
Re: PO118 Engine Temp code
« Reply #3 on: February 07, 2020, 07:50:24 PM »


Not sure the ET sensor would affect motor on cold start



Have rarely had them fail.  Only a couple times I can remember ever.  One of those two did effect start, idle speed, and occasional stalls at idle.  What made sense at the time was that the system was trying to supply fuel and air settings for a bike it thought was not at full operating temperature when the engine was actually hot. 
Logged

AZSERK

  • Newbie
  • *
  • Offline Offline
  • Posts: 14
  • www.CVOHARLEY.com
    • AZ

Re: PO118 Engine Temp code
« Reply #4 on: February 11, 2020, 03:08:30 PM »

It's ALIVE :bananarock:
Replaced the ET Sensor switch and the check engine light cleared.  The bike springs to life on the first crank now, idles very smoothly, and scoots when you twist its tail.
Happy Ending :orange: :mango: :apple: :carrot: :cucumber: :pineapple: :pepper: :2vrolijk_21:
Logged

Twolanerider

  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 50536
  • EBCM #1.5 Emeritus DSP # ? Critter Gawker #?
    • MO


    • CVO1: 2000 Triple Red Screamin' Eagle Road Glide
    • CVO2: 2002 Candy Brandywine Screamin' Eagle Road King
    • CVO3: 1999 Arresting Red FXR2
Re: PO118 Engine Temp code
« Reply #5 on: February 12, 2020, 12:04:12 AM »

It's ALIVE :bananarock:
Replaced the ET Sensor switch and the check engine light cleared.  The bike springs to life on the first crank now, idles very smoothly, and scoots when you twist its tail.
Happy Ending :orange: :mango: :apple: :carrot: :cucumber: :pineapple: :pepper: :2vrolijk_21:



Out Freaking Standing

Now ride that Bitch!
Logged
 

Page created in 0.136 seconds with 24 queries.