Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Gettinold]

Something to keep in mind, even with a fairly stable jack like my J&S - don't forget to block up the front tire 

I was using a pile of boards until I remembered I had this jack in the shed. Works good and doesn't slip out as easy as the wood was.

I also tie wrapped the rotor to the fork to help keep the wheel from moving.

    

[porthole]

   

Making ya nervous Davey?

[Gettinold]

Havent you spent eough on yet. $$$$$$$$$$   

[porthole]

Yeah ---


Hey Brian -did you get a tracking number?

[hogasm]

Yeah ---


Hey Brian -did you get a tracking number?

No, but I will check on it in the morning

[hogasm]

 TINTON FALLS,
NJ,  US    03/17/2009    6:00 A.M.    OUT FOR DELIVERY
   03/17/2009    2:35 A.M.    ARRIVAL SCAN
HORSHAM,
PA,  US    03/17/2009    1:03 A.M.    DEPARTURE SCAN
HORSHAM,
PA,  US    03/16/2009    2:54 P.M.    ARRIVAL SCAN
RALEIGH,
NC,  US    03/16/2009    4:40 A.M.    DEPARTURE SCAN
RALEIGH,
NC,  US    03/15/2009    10:53 P.M.    ARRIVAL SCAN
MANTEO,
NC,  US    03/13/2009    8:43 P.M.    DEPARTURE SCAN
   03/13/2009    5:59 P.M.    ORIGIN SCAN

Tracking results provided by UPS:  03/17/2009 11:45 A.M.  ET

[Talon]

Might be a little late! 

[1711tab]

The night started out good and ended with an "oh chit" and that sinking feeling you get in your gut.

Put a bid (actually a buy it now) on Monday and it was here on Tuesday.

Make sure you install the Baker sealed bearing in your inner primary...

[1711tab]

Love my OD6 and 3.37.   

I LOVE MY OD6 R Ratio with 2.94 first and .80 final...

[porthole]

Make sure you install the Baker sealed bearing in your inner primary...

I will, just as soon as one gets here that was was honed out to fit 

[Trapperdog]

Duane, you've got me hooked on this install thread, keep us updated upon the parts arrival!  Roger

[erniezap]

Thinking about a 6 speed Roger? 

[hogasm]

Thinking about a 6 speed Roger? 

No Roger NO!!!

See all the chit that happens when you change.....tell him Duane....tell him

[Trapperdog]

Thinking about a 6 speed Roger? 

No Roger NO!!!

See all the chit that happens when you change.....tell him Duane....tell him

   You guys so funny... I'm one of the lucky ones, ole' red came with a six speed. I was thinking of installing one in the '05 I used to have but didn't have the cahones to do it. After reading of Duane's problems I'm sure glad I didn't. I used to tear into my Maico 400's (motocross bike) gearbox many years ago after every race. Poorly built trany that kept loosing gears and forks. Maybe not using the clutch had something to do with it. .My hat's off to Duane though, whole different ball game with these trany's.

[porthole]

Alright, so Brian mentioned the baker bearing.
Just what is a Baker bearing?

Baker distributes a one piece sealed bearing for the inner primary that replaced the HD separate race and roller bearing.

The picture below is the HD standard two piece bearing. The sleeve sitting above the bearing is a press fit on the the trans mainshaft. With higher HP engines there is a problem with these sleeves; they tend to move on the main shaft either towards the main drive gear, damaging the gear and seal or move towards the inner primary and damage the inner primary bearing.