Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 2 [All]

Author Topic: Cruise Control Disengage (Front Brake)  (Read 13201 times)

0 Members and 1 Guest are viewing this topic.

harleychef2011

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 148
  • www.CVOHARLEY.com
    • CA


    • CVO1: 2014 Road King - Tribal Orange & Galactic Black
Cruise Control Disengage (Front Brake)
« on: January 31, 2015, 03:13:34 PM »

Anyone else having an issue with the cruise control disengaging using the front brake lever?  Quite a few times now I have squeezed the front brake lever to turn off the cruise and the pressure is enough to lunge the bike (braking) but when I release the cruise is still active and I speed up again.  No problem if I squeeze the lever for 2+ seconds....but it used to turn off with just a "flick" of the brake.  I brought it to my dealers attention and (of course) they couldn't "replicate the issue" (I'm pretty sure that is mechanic talk for 'I don't want to deal with it').

Anyone else have this problem?
Logged
2014 CVO Road King
V&H Power Duals
V&H Carbon Fiber Tip Pipes
HD Super Tuner & Dyno - 98.7 HP 112.9TQ
RoadTech 665 GPS
Mucho HD Add-Ons!!!

Bav

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 622


    • CVO1: 2018 CVO Road Glide Custom
Re: Cruise Control Disengage (Front Brake)
« Reply #1 on: January 31, 2015, 03:23:02 PM »

Yes. I have noticed this as well and stopped relying on the brake to turn off the cruise as you would expect. I like to use the cruise only when there is very light traffic and the need to brake is hopefully reduced. Still it's not an excuse and it should work as well as it does in my car.


Sent from my iPad using Tapatalk
Logged
Using Tapatalk

Twolanerider

  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 50536
  • EBCM #1.5 Emeritus DSP # ? Critter Gawker #?
    • MO


    • CVO1: 2000 Triple Red Screamin' Eagle Road Glide
    • CVO2: 2002 Candy Brandywine Screamin' Eagle Road King
    • CVO3: 1999 Arresting Red FXR2
Re: Cruise Control Disengage (Front Brake)
« Reply #2 on: January 31, 2015, 06:04:25 PM »

Have you had someone watch to see if the brake light is illuminating all the time when the front lever is being pulled?
Logged

FLSTFI Dave

  • IBA 69147
  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 6709

    • CVO1: 2023 FLTRXSE Whiskey Neat
    • CVO2: 2021 RA1250S Pan America Special
    • CVO3: 2003 Fatboy, 95"quot, S&ampS 570 gear drive cam
Re: Cruise Control Disengage (Front Brake)
« Reply #3 on: January 31, 2015, 08:26:45 PM »

Honestly have never tired to shut cruise off using front brake unless it was a panic type slow down or stop.  Usually when using cruise if I need it off due to approaching slower traffic I just roll the throttle forward and cruise shuts off, then position throttle where I need it.

Sounds like the issue might be with the front brake switch though.
Logged
2023 FLTRXSE Whiskey Neat
2021 RA1250S Pan America Special
2019 FLTRXSE Red Pepper / Magnetic Gray Traded
2018 FLTRXSE Gunship Gray  Traded
2017 FLHXSE  Starfire Black / Atomic Red  Traded
2015 FLTRUSE Abyss Blue / Crushed Saphire Traded
2013 FLHRSE5 Diamond Dust 117  Traded
2012 FLTRXSE White Gold Pearl / Starfire Black  Traded
2009 FLTRSE3 Silver/Titanium  Traded
2003 Fatboy, real fire paint set,

CVODON

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2420
    • FL

    • CVO1: 15 FLTRUSE
Re: Cruise Control Disengage (Front Brake)
« Reply #4 on: February 01, 2015, 06:11:04 PM »

I use the cruise, constantly on every ride. I always hit front brake to cancel as I hardly ever use the rear brake unless panic stop. Never had a problem on any of the bikes over the years with touch of frt brake lever not kicking it off. Make dealer due elec pin-point test on circuit. Complain it is a safety issue, complain loudly.
Logged

Gandrtravis

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 236
  • www.CVOHARLEY.com
    • AB


    • CVO1: 2008 cvo dyna inferno red and desert black sold
    • CVO2: 2014 cvo road king tribal orange and galactic black traded
    • CVO3: 2018 cvo road glide gunship grey
Re: Cruise Control Disengage (Front Brake)
« Reply #5 on: February 02, 2015, 04:43:27 PM »

I have also ran into this problem on occasion but I'm not sure why it does it sometimes it seems to work I just use my rear brake and it seems to work better. Maybe harley will recall it eventually lol.
Logged

Billy

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 736
  • FLHRSEI.ORG

    • CVO1: 2007 SERK
    • CVO2: 2014 SERK
Re: Cruise Control Disengage (Front Brake)
« Reply #6 on: February 02, 2015, 05:08:04 PM »

My Tech said that it is a delay to the brake module. But I have found that it is easier to use the throttle as you do not give off a brake light and alert others . Billy
Logged
2014 SERK Tribal Orange Wild one 501 apes Powder coated gloss black, Mustang Seat with backrest, King tour pack with smoked lights, LED aux lights, CD Dynamic front ringz, CD custom license plate with LED turns and brake light, Zumo 660 mounted on bar, Klock Werks 17 inch Flare windshield, Saddle bag guards, Added LED turn indicators in handle bar cover, Engine guard foot pegs

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: Cruise Control Disengage (Front Brake)
« Reply #7 on: February 02, 2015, 05:42:28 PM »

My Tech said that it is a delay to the brake module. But I have found that it is easier to use the throttle as you do not give off a brake light and alert others . Billy

I seriously doubt that.  Is there also a delay for the brake lights to come on?  The speed of the electrons in that circuit is astonishingly fast, and the cruise on the late model bikes is handled by the ECM and the Electronic Throttle Control.  Both of those have very fast response times as well.

I've always personally preferred tapping the front brake, but to each their own.  At least you have multiple choices for disengagement, from turning off the switch, using either brake, rolling the throttle back, or pulling the clutch lever.  If all of those fail, throw out the optional H-D brand anchor and hold on.

Jerry
Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

EZRIDN

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 674
  • FLHRSEI.ORG - Paying tribute to an American legend
    • NE


    • CVO1: FLHRSEI2
    • CVO2: 1947 FL
    • CVO3: 2004 FXSTI
Re: Cruise Control Disengage (Front Brake)
« Reply #8 on: February 02, 2015, 07:19:14 PM »

I've always personally preferred tapping the front brake, but to each their own.  At least you have multiple choices for disengagement, from turning off the switch, using either brake, rolling the throttle back, or pulling the clutch lever.  If all of those fail, throw out the optional H-D brand anchor and hold on.   Jerry

I always tap the front brake as well and have had no issues.  But, I am curious Jerry...which H-D anchor do you recommend...painted or chrome and what length of chain should one consider?   
Logged
"My goal is to become that old person everyone is afraid to take out in public."

"I would like to apologize to anyone I have not yet offended...please be patient...I will get to you shortly ."

HD Owners Tip #39:  "Although the manual doesn't mention it, some swearing seems to help most machines run a little better."

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: Cruise Control Disengage (Front Brake)
« Reply #9 on: February 02, 2015, 07:43:21 PM »

Come on now, you know it wouldn't be an official H-D anchor unless it was chromed (most likely cheap Chinese chrome of course). ;)  I think about 50 feet of official Harley chain should do the trick.  A pair of official Harley branded Depends might also be a good idea.

Jerry
Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

BritGuy

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1000
  • www.CVOHARLEY.com
    • BC

Re: Cruise Control Disengage (Front Brake)
« Reply #10 on: February 10, 2015, 04:49:12 PM »

Just read this thread, had to laugh at the anchor and chain! Seriously, I have the same 2014 model hibernating at the moment, but anything to do with cruise not working is a worry. Harleychief2011, has the problem been identified and fixed yet? Particularly worrying as Jerry said, everything is controlled by the ECU  and if HAL has invaded the cruise control, what else may or may not stop working without any warning?
Logged

greglyon

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1444
  • 2013 FLHRSE5
    • AZ


    • CVO1: FLHRSE5
    • Phillips and Lyon LLC
Re: Cruise Control Disengage (Front Brake)
« Reply #11 on: February 10, 2015, 05:29:16 PM »

I have a 2013 never had this problem. Always tap the front brake to release the cruise. Get it fixed. In an emergency stop you don't want to be thinking about this instead of the problem at hand.   
Logged
"A clear conscience is usually the sign of a bad memory"

casbar

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 158


    • CVO1: 2014 RK
Re: Cruise Control Disengage (Front Brake)
« Reply #12 on: February 13, 2015, 02:37:41 AM »

Mine is still working ok, well it was last weekend. Take it to the dealer the bike must still be under warrenty
Logged

harleychef2011

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 148
  • www.CVOHARLEY.com
    • CA


    • CVO1: 2014 Road King - Tribal Orange & Galactic Black
Re: Cruise Control Disengage (Front Brake)
« Reply #13 on: February 15, 2015, 02:27:10 PM »

Thanks for all the replies everyone!  Sorry its been awhile...slammed with work and then got into a major (60mph) accident on Monday.  Totaled the car...would have been dead on the bike!  Any other day I would have been on my motorcycle but decided to take the car because we just drove in from San Diego (400 miles) that morning!

I didnt even know you could disengage the cruise by rolling forward!  That is why I love this forum! 

Definitely going to have it checked again during my next service!  Maybe I'll hit them up for one of those chrome anchors!  LOL!
Logged
2014 CVO Road King
V&H Power Duals
V&H Carbon Fiber Tip Pipes
HD Super Tuner & Dyno - 98.7 HP 112.9TQ
RoadTech 665 GPS
Mucho HD Add-Ons!!!

FLSTFI Dave

  • IBA 69147
  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 6709

    • CVO1: 2023 FLTRXSE Whiskey Neat
    • CVO2: 2021 RA1250S Pan America Special
    • CVO3: 2003 Fatboy, 95"quot, S&ampS 570 gear drive cam
Re: Cruise Control Disengage (Front Brake)
« Reply #14 on: February 15, 2015, 08:11:03 PM »

Thanks for all the replies everyone!  Sorry its been awhile...slammed with work and then got into a major (60mph) accident on Monday.  Totaled the car...would have been dead on the bike!  Any other day I would have been on my motorcycle but decided to take the car because we just drove in from San Diego (400 miles) that morning!

I didnt even know you could disengage the cruise by rolling forward!  That is why I love this forum! 

Definitely going to have it checked again during my next service!  Maybe I'll hit them up for one of those chrome anchors!  LOL!

Glad you were in the car, not the bike.  Sorry you were in a accident.

For me, rolling it forward is the way I do it 90% of the time.  When I am on cruise, I usually do not need to stop, or even slow down quickly.  I just need to coast down a bit due to traffic. 

That said front brake should disengage it.
Logged
2023 FLTRXSE Whiskey Neat
2021 RA1250S Pan America Special
2019 FLTRXSE Red Pepper / Magnetic Gray Traded
2018 FLTRXSE Gunship Gray  Traded
2017 FLHXSE  Starfire Black / Atomic Red  Traded
2015 FLTRUSE Abyss Blue / Crushed Saphire Traded
2013 FLHRSE5 Diamond Dust 117  Traded
2012 FLTRXSE White Gold Pearl / Starfire Black  Traded
2009 FLTRSE3 Silver/Titanium  Traded
2003 Fatboy, real fire paint set,

AMEDD_SFC

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 479
  • 2014 CVO Limited
    • TX


    • CVO1: 2014 CVO Limited - The Big Red One
Re: Cruise Control Disengage (Front Brake)
« Reply #15 on: May 12, 2015, 12:40:40 PM »

Hi all:

I went on a trip out to MS this last weekend and experienced this same issue - intermittently.  Apparently, my memory is not as bad as I thought, because I remembered this thread.

Unfortunately, I see there was no resolution.  I did learn the "roll-on" method here, but I will forego the anchor.

I am hear to tell you though, the first time you learn that the front brake is not going to cancel the cruise, you are pretty quickly looking for an alternative!

Anyway, I am taking my bike in for a tire so I will have them look at the issue and post back here with any 411.

Regards,

Mark
Logged

Mark B.
SFC, USA (RET)

cembo

  • Newbie
  • *
  • Offline Offline
  • Posts: 34
  • Time To Ride
    • NJ

    • CVO1: FLHRSE6
Re: Cruise Control Disengage (Front Brake)
« Reply #16 on: May 12, 2015, 01:40:54 PM »

Just saw this thread and had to report that I had the same happen to me over the weekend! Tried it again yesterday and it worked as intended. I hate to take it to the dealership and receive the same "could not replicate" response but think that this is a very serious issue!!! While there might be many ways of disengaging it, you might easily end up in a situation with no time to think about it. I fear that HD will wait for some accidents to happen before they issue yet another recall...
Logged

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: Cruise Control Disengage (Front Brake)
« Reply #17 on: May 12, 2015, 01:44:37 PM »

Try tapping the rear brake instead and see what happens.  Or maybe the electrons in the rear brake circuit are just as slow as the ones in the front brake circuit (but only occasionally)? ;)

I'd love for someone who has this problem to run a little test to see if the brake lights also have the same issue, ie. slow to respond to pedal or lever movement, or require excessive pressure before they respond.  Probably need a big mirror or a dark garage.

Jerry
Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

Tractor Bubba

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 106
  • Life's Short - Eat your dessert first!
    • GA


    • CVO1: '19 FLHTK Ultra Limited - Silver Flux/Black Fuse
    • CVO2: '14 FLHRSE Road King - Tribal Orange/Galactic Black
Re: Cruise Control Disengage (Front Brake)
« Reply #18 on: May 12, 2015, 08:56:53 PM »

...I've always personally preferred tapping the front brake, but to each their own.  At least you have multiple choices for disengagement, from turning off the switch, using either brake, rolling the throttle back, or pulling the clutch lever.  If all of those fail, throw out the optional H-D brand anchor and hold on.

Jerry

Ha!  I thought maybe Jerry's "...throw out the anchor..." comment was referring to the "BoB"!
Logged
2019 FLFRTK
2014 FLHRSE6

AMEDD_SFC

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 479
  • 2014 CVO Limited
    • TX


    • CVO1: 2014 CVO Limited - The Big Red One
Re: Cruise Control Disengage (Front Brake)
« Reply #19 on: May 15, 2015, 05:33:56 PM »

Allcon:

In an update, it turns out that my front brake switch is faulty.  Apparently, I was getting no brake light which is connected to the cruise via ECM.  The warranty is going to replace the switch assembly, which according to the tech, is "pricey.  They have to replace the entire switch module on the right side.  According to Ronnie's HD $231.

Now, that there is some engineering Mother Harley.

So there you go.  If your front brake is failing to disengage the cruise, check your brake lights, too.

Mark
Logged

Mark B.
SFC, USA (RET)

Twolanerider

  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 50536
  • EBCM #1.5 Emeritus DSP # ? Critter Gawker #?
    • MO


    • CVO1: 2000 Triple Red Screamin' Eagle Road Glide
    • CVO2: 2002 Candy Brandywine Screamin' Eagle Road King
    • CVO3: 1999 Arresting Red FXR2
Re: Cruise Control Disengage (Front Brake)
« Reply #20 on: May 15, 2015, 05:44:58 PM »

Have you had someone watch to see if the brake light is illuminating all the time when the front lever is being pulled?
Logged

sadunbar

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 11416
  • EBCM # Stealth - SSBS # 1.1 - SoA # Z&E2525 .01%
    • IL


    • CVO1: 2007 FLHTCUSE2
    • CVO2: 2000 FXR4
Re: Cruise Control Disengage (Front Brake)
« Reply #21 on: May 15, 2015, 08:48:04 PM »

Have you had someone watch to see if the brake light is illuminating all the time when the front lever is being pulled?


 ::)
Logged
2007 Screamin Eagle Ultra Classic - Light Candy Cherry and Black Ice
Screamin Eagle 120r
Revolution Performance EMS
Fuel Moto Jackpot headpipes and 4.5" Pro Touring Mufflers
HPI 55mm Throttle Body w/5.3 injectors
BDL clutch w/VPC92T
Traxxion AK-20
Legend Air Suspension
Brembo Brake Calipers/Rotors
Garmin Zumo
575 Chubby's
Bushtec Quantum

casbar

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 158


    • CVO1: 2014 RK
Re: Cruise Control Disengage (Front Brake)
« Reply #22 on: May 17, 2015, 03:51:32 AM »

Allcon:

In an update, it turns out that my front brake switch is faulty.  Apparently, I was getting no brake light which is connected to the cruise via ECM.  The warranty is going to replace the switch assembly, which according to the tech, is "pricey.  They have to replace the entire switch module on the right side.  According to Ronnie's HD $231.

Now, that there is some engineering Mother Harley.

So there you go.  If your front brake is failing to disengage the cruise, check your brake lights, too.

Mark

Yep been there and got the T shirt. My entire switch module on the right side had to be replaced. The bike was delivered to me new, with a cut off switch that didn't work, had to stall the bike to switch the engine off! Took Harley 6 weeks to get a switch to the UK. Replaced under warranty
Logged

cembo

  • Newbie
  • *
  • Offline Offline
  • Posts: 34
  • Time To Ride
    • NJ

    • CVO1: FLHRSE6
Re: Cruise Control Disengage (Front Brake)
« Reply #23 on: May 22, 2015, 04:34:48 PM »

Just got back from the dealer as I had the cruise control once again not disengage with the front brake. I did check the brake lights multiple times now and it always worked fine. Anyways, while the bike did not show error codes on the speedo, once we hooked it up to their Diagnosis system sure enough it had logged Code 0572 multiple times over the last 3000miles! It is the Switchpack assemblyr on the right side (Part no: 71500163A) and will need to be replaced under warranty. I am convinced that there are many of us out there riding with this faulty unit without even realizing...
Logged

harleychef2011

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 148
  • www.CVOHARLEY.com
    • CA


    • CVO1: 2014 Road King - Tribal Orange & Galactic Black
Re: Cruise Control Disengage (Front Brake)
« Reply #24 on: June 01, 2015, 02:53:13 PM »

Just got back from the dealer as I had the cruise control once again not disengage with the front brake. I did check the brake lights multiple times now and it always worked fine. Anyways, while the bike did not show error codes on the speedo, once we hooked it up to their Diagnosis system sure enough it had logged Code 0572 multiple times over the last 3000miles! It is the Switchpack assemblyr on the right side (Part no: 71500163A) and will need to be replaced under warranty. I am convinced that there are many of us out there riding with this faulty unit without even realizing...

Thanks for the update man!  I'm taking the bike in for my 20K soon.... so I will show them this thread.  At least I know I'm not crazy and see others are having the same problem!  I genuinely appreciate the feedback!

Ride safe my friends!

Logged
2014 CVO Road King
V&H Power Duals
V&H Carbon Fiber Tip Pipes
HD Super Tuner & Dyno - 98.7 HP 112.9TQ
RoadTech 665 GPS
Mucho HD Add-Ons!!!

cembo

  • Newbie
  • *
  • Offline Offline
  • Posts: 34
  • Time To Ride
    • NJ

    • CVO1: FLHRSE6
Re: Cruise Control Disengage (Front Brake)
« Reply #25 on: June 03, 2015, 08:59:26 PM »

Thanks for the update man!  I'm taking the bike in for my 20K soon.... so I will show them this thread.  At least I know I'm not crazy and see others are having the same problem!  I genuinely appreciate the feedback!

Ride safe my friends!

Your most welcome! Be safe and report back.
Logged

AMEDD_SFC

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 479
  • 2014 CVO Limited
    • TX


    • CVO1: 2014 CVO Limited - The Big Red One
Re: Cruise Control Disengage (Front Brake)
« Reply #26 on: June 04, 2015, 05:33:14 PM »

Dealer replaced my switch block yesterday.  They had to fiddle with the original one to replicate the problem as it was intermittent.  That was not an issue, because they apparently know about the defect.  The technician commented that the new switch blocks are a different color now.

Sounds like a stealth recall or product program that mother Harley is content with waiting on until customers complain. I think it is a safety issue and there are enough faulty switch blocks our there to warrant a recall.  Just my 2c.

M

Logged

Mark B.
SFC, USA (RET)

cembo

  • Newbie
  • *
  • Offline Offline
  • Posts: 34
  • Time To Ride
    • NJ

    • CVO1: FLHRSE6
Re: Cruise Control Disengage (Front Brake)
« Reply #27 on: June 04, 2015, 09:26:33 PM »

Dealer replaced my switch block yesterday.  They had to fiddle with the original one to replicate the problem as it was intermittent.  That was not an issue, because they apparently know about the defect.  The technician commented that the new switch blocks are a different color now.

Sounds like a stealth recall or product program that mother Harley is content with waiting on until customers complain. I think it is a safety issue and there are enough faulty switch blocks our there to warrant a recall.  Just my 2c.

M

Agreed 100%! I don't want to imagine what will happen if it happens by surprise at the wrong time, in the wrong place...
I think the suffix "A" was added to the original part number to indicate the new one. If I am not mistaken the part should be around $230 or so. Bike will be going in soon.
Logged

Bav

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 622


    • CVO1: 2018 CVO Road Glide Custom
Re: Cruise Control Disengage (Front Brake)
« Reply #28 on: June 21, 2015, 11:36:46 AM »

Mine is definitely not properly disengaging the cruise control. Just tested it today and it wouldn't cancel the cruise control if you pulled the front brake lever unless you pulled it really hard. A couple of light pulls did nothing other than lightly apply the brakes. Lightly pressing the rear brake cancelled it ok as did pulling the clutch lever. I'm going to get it looked at when its in for its 15k and show them this thread.


Sent from my iPad using Tapatalk
Logged
Using Tapatalk

Billy

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 736
  • FLHRSEI.ORG

    • CVO1: 2007 SERK
    • CVO2: 2014 SERK
Re: Cruise Control Disengage (Front Brake)
« Reply #29 on: September 18, 2018, 08:15:34 AM »

I have had the same issue again. It seems to not turn off the cruise the first time I use it with the front brake. I had time to play with the front brake. It would not turn off the cruise after  four times I then touched the rear brake and it turned off. After that the front brake would turn off cruise on first light tap. Tech could not duplicate on last visit as it only happened once before. Tech said they would replace a module if it happens again. I will be at dealer today to have the part ordered.  Billy
Logged
2014 SERK Tribal Orange Wild one 501 apes Powder coated gloss black, Mustang Seat with backrest, King tour pack with smoked lights, LED aux lights, CD Dynamic front ringz, CD custom license plate with LED turns and brake light, Zumo 660 mounted on bar, Klock Werks 17 inch Flare windshield, Saddle bag guards, Added LED turn indicators in handle bar cover, Engine guard foot pegs
Pages: 1 2 [All]
 

Page created in 0.229 seconds with 24 queries.