CVO Technical > Electronic Toys and Gadgets
load equalizer/ load resister suggestions?
joejoebobo:
Looks like there is a lot out there for load equalizers (LE) and load resisters (LR) ... looking to see if there are any difference between the 2? What would you recommend? Some are plug and play and some require wire splicing. Some get really hot while others could cause damage if you run your hazards. Is there any harm with not running LE/LR?
I have some nice bullet style front turn signal LEDs for my 2010 CVO SG and get hyper flashing every now and then (sometimes it's after 5 sec and sometimes after 30+sec). Yes, it bugs me... I paid @$40 for the LED turn signals and didn't realize to get rid of hyper flashing on '13 and older models, it'll require LE/LR up to $70. The rear turn signals include stock LEDs so I would only need the LE/LR for the front. Am I just being cheap or are their cheaper alternatives?
Also, not sure if it's related but I'm also running (2) LED H11 Headlight Bulbs. When running the LED headlight bulbs and the stock incandescent front turn signal bulbs, I'm pretty sure I never got hyper-flashing.
GregKhougaz:
When I had my '09, I got load equalizers from Custom Dynamics, Kuryakyn and others. All worked fine.
iski:
Used Custom Dynamics LE for the LEDs on my 2010. Worked great.
Glenncarp:
--- Quote from: joejoebobo on February 03, 2020, 09:45:36 AM ---Looks like there is a lot out there for load equalizers (LE) and load resisters (LR) ... looking to see if there are any difference between the 2? What would you recommend? Some are plug and play and some require wire splicing. Some get really hot while others could cause damage if you run your hazards. Is there any harm with not running LE/LR?
I have some nice bullet style front turn signal LEDs for my 2010 CVO SG and get hyper flashing every now and then (sometimes it's after 5 sec and sometimes after 30+sec). Yes, it bugs me... I paid @$40 for the LED turn signals and didn't realize to get rid of hyper flashing on '13 and older models, it'll require LE/LR up to $70. The rear turn signals include stock LEDs so I would only need the LE/LR for the front. Am I just being cheap or are their cheaper alternatives?
Also, not sure if it's related but I'm also running (2) LED H11 Headlight Bulbs. When running the LED headlight bulbs and the stock incandescent front turn signal bulbs, I'm pretty sure I never got hyper-flashing.
--- End quote ---
I added Custom Dynamic from turn signals to Road Glide, no issues, few moths later added rear ( I have the bullet turn/brake lights in back) started getting quick flashing turn signals. Was at HD to have heated grips installed and asked them to also add load EQ's to correct issue. When bike was done Service guy told me all tech did was teak module and load EQ's are not needed any longer. Hmm, something for free from HD, so weird, but so far, I have had zero issues. Happy as a clam at that bit of info.
joejoebobo:
Thanks everyone... I'll look into some further options...
Glenncarp - I've too have recently learned that on '14 and newer models, you can follow the custom dynamics turn signal sync procedure below and it will auto correct the hyper flashing... '14 and newer models come equipped with canbus/BCM electrical systems.
1. Turn Ignition on, but do not start the bike.
2. Turn on 4 way hazards by pressing the hazard button on the controls.
3. Turn the Ignition off letting hazards run. IF the bike has security they will flash 5 or 6 times and then pause. This is normal. They will go back to flashing normal hazard mode.
4. Let hazards run 1-2 minutes.
5. Turn Ignition back on.
6. Turn off hazards.
7. Turn Ignition off and then back on.
8. Check function of both turn signals.
Navigation
[0] Message Index
[#] Next page
Go to full version