Topic: 2010 RG windshield trim piece. (Read 5751 times)

NETacoma03Fatboy · « **on:** March 14, 2012, 12:43:06 AM »

My Buddies could not get this on my 2010 RG. Any suggestions? Does the rubber trim stay on or does it come off? Thanks.

http://www.harley-davidson.com/gma/gma_product.jsp?WebLogicSession=KyRyhTOmIh50bw04TVcKKaN6NvQm52vo3UOb5QM1y3LR2UChhr34!3583657!hiwpbmsp04.ihd.hd!7005!8005&PRODUCT%3C%3Eprd_id=845524448769913&FOLDER%3C%3Efolder_id=2534374302287493&ASSORTMENT%3C%3East_id=2534374302287493&bmUID=1253200372418&bmLocale=en_US

kiwihog · « **Reply #1 on:** March 14, 2012, 12:54:25 AM »

do you have the stock w/shield???

NETacoma03Fatboy · « **Reply #2 on:** March 14, 2012, 01:05:06 AM »

No. 12" Klock Werks.

kiwihog · « **Reply #3 on:** March 14, 2012, 02:12:29 AM »

thats the problem I think...I have a Clearview and just got the trim piece for it but it wont fit it appears the angle of the shield is different I just put it with the rest of the crap I bought and will probably never use.. it does fit with the small black 6" harley shield I have for summer so will use it on that..

NETacoma03Fatboy · « **Reply #4 on:** March 14, 2012, 08:12:57 PM »

well that is a bugger. Thanks for the advice.

XCESS · « **Reply #5 on:** March 31, 2012, 04:59:05 PM »

I have the same problem. I just took delivery of a new Maple metallic with the stock new Windsplitter Windshield. In the new supplement to the P&A catalogue it says under the picture "shown with a windsplitter windshield". My guys at the dealership tried for over an hour to make it fit but no luck.Has anyone out there put the black gloss trim on their New CVO RG with the stock windsplitter not the standard RG windshield or any other king of windshield.

petewerner · « **Reply #6 on:** March 31, 2012, 05:15:40 PM »

Put it on my RGC with the CW 12" and no problems. It requires some work th get it right, the offset holes need to be adjusted right and this process took me (not a wrench) a couple of hours to get it all laying flat. No the stock rubber goes away. Use just the rubber it the kit!

King Glide · « **Reply #7 on:** March 31, 2012, 08:36:42 PM »

I did it with the Harley wind splitter. It was a pita. I used no rubber except what is on the trim, I enlarged the slots in the shield and basically clamped the shield tight using the trim. Have to admit it's a bit ugly under the trim but nobody will ever see it so no prob. Just cover everything including the floor, I must have dropped the trim a dozen times trying to make it fit.

NETacoma03Fatboy · « **Reply #8 on:** April 01, 2012, 01:43:34 AM »

and this was the HD trim and not the Kuryakyn. correct?

wish you guys were here.......

kiwihog · « **Reply #9 on:** April 01, 2012, 02:10:13 AM »

According to Long Ride Shields the hole spacing is different on the CVO bikes compared to the non CVO not sure if thats right but when I spoke to them last week they gave up a sale because of this I had already ordered and mentioned CVO Harley when he asked if it was a CVO .. they were going to have to set up equipment to make it special with the different hole spacing I was going to replace Clearview shield as the angle of the shield was leaving a 1/4" gap all the way across at the bottom of the shield ..I even went out and tried again Friday to make sure I wasnt doing something wrong..

motor1 · « **Reply #10 on:** April 01, 2012, 10:08:47 AM »

Hey Kiwihog, have a Clearview on my FLTRUSE, used the stock windshield gasket (carefully peel from stock shield) and have a windshield that fits tight and snug, no space, no gaps.

kiwihog · « **Reply #11 on:** April 01, 2012, 11:53:49 AM »

Quote from: motor1 on April 01, 2012, 10:08:47 AM

Hey Kiwihog, have a Clearview on my FLTRUSE, used the stock windshield gasket (carefully peel from stock shield) and have a windshield that fits tight and snug, no space, no gaps.

Yep I got the windshield on with the OE rubber but cant get the windshield chrome trim cover on seems because of the angle I wanted to cover the holes because the black decal on the inside of the shield has rippled at the screw holes and looks ugly shield was installed last year by Clearview at AZ bikeweek works great and Clearview sent me a replacement sticker but decided to wait till I cant stand the look any longer

King Glide · « **Reply #12 on:** April 01, 2012, 08:14:02 PM »

Yes, Harley wind splitter and black Harley trim.

XCESS · « **Reply #13 on:** April 01, 2012, 10:36:27 PM »

thanks King roadglide,i'm going to pick one up this week and try it. You say you have to enlarge the holes in the windsplitter shield? can you post a picture of the finished product. thx

King Glide · « **Reply #14 on:** April 01, 2012, 11:54:11 PM »

I'll try tomorrow, because I'm working with a first gen IPAD it might not be easy. Anyway once it was done it looks perfect but my trade was as a tool and die maker and that makes re-designing stuff easy.

King Glide · « **Reply #15 on:** April 02, 2012, 12:19:05 PM »

ok, here you go.

King Glide · « **Reply #16 on:** April 02, 2012, 12:26:10 PM »

another...

GregKhougaz · « **Reply #17 on:** April 02, 2012, 12:29:27 PM »

Looks great!

petewerner · « **Reply #18 on:** April 03, 2012, 08:59:13 AM »

Nice! When the dealers meeting catalog came out it was the first time I saw it! I replaced my chrome for the new black trim that I had been looking for, as soon as I saw it I ordered it!! It entirely changed the look...

petewerner · « **Reply #19 on:** April 03, 2012, 09:30:58 AM »

And this, poor quality photos, my phone...

XCESS · « **Reply #20 on:** April 08, 2012, 01:19:28 AM »

Thyx for the pix . I plan on giving it a try on my maple woody.

Author Topic: 2010 RG windshield trim piece. (Read 5751 times)