Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 2 3 [All]

Author Topic: 2014 Limited Check engine light, red temperature light P1019  (Read 15371 times)

0 Members and 1 Guest are viewing this topic.

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4808
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010

17,500 miles on 2014 Limited..  Was on a group ride with a OhioDave and a few friends last week.  Check engine light came on as well as red overheat temperature light..  Bike ran fine.  Rode about 10 miles home after it happened.
Was full of coolant.  Removed water pump cover, turned ignition on, rolled throttle half way and held it and both cooling fans and water pump ran as they should.  Pulled P1019 from odometer.  Read thru electric diagnosis  manual and said to replace coolant temperature sensor.  Replaced sensor in LH lower radiator and all is well..
May be able to help someone.  Should not have gone bad in 3 years 17,500 miles but could have been water pump.  Sensor was $25.00..  FWIW
Logged

OBB

  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 5184
  • aka Ohiobellboy
    • OH


    • CVO1: 2011 Slate/Black SERGU** traded
    • CVO2: 2015 Double Blue SERGU
    • CVO3: 2012 SERG Blue
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #1 on: June 06, 2017, 08:53:37 AM »

Good info there Bob. Thank You.

Sent from my XT1254 using Tapatalk

Logged
PHOTOBUCKET IS HOLDING MY PIX HOSTAGE!!!

rnich56

  • Newbie
  • *
  • Offline Offline
  • Posts: 7
  • www.CVOHARLEY.com
    • FL

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #2 on: June 06, 2017, 01:03:08 PM »

Hi,

I just had this same problem while on a trip riding in the Smokies.  My problem turned out to be chafing ET sensor wire on an upper cooling hose under the tank.  I posted a picture showing more chafing wires under the tank.  My post is under CVO Limited, chafing wires.

Rick
Logged

Major Tom

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 372
    • LA


    • CVO1: Blue n Blue 2015 FLTRUSE - Lucille
    • CVO2: Grey n' Black 2011 FLTRUSE - Bertha (Sold)
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #3 on: June 06, 2017, 02:26:15 PM »

I replaced Lucille's coolant pump last Aug at Sioux Falls after similar issues. It's a common problem which I understand may/did occur intermittently because of a vacuum lock or shot/damaged sensor or the pump itself. Mine was the pump. Thanks
Thanks for sharing.

Cheers Tom


Sent from my iPhone using Tapatalk
Logged

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4808
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #4 on: May 08, 2018, 12:56:08 PM »

5-18 update, 24,600 miles

Started getting P1019 code again in bike week in Daytona in March.  Ordered new w/pump and thermostat from Surdyke.  Hope this fixes it and not wasting money on replacing good parts.  Not a hard install for water pump and thermostat  replacement.
Logged

shaochieh.young

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • www.CVOHARLEY.com

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #5 on: May 10, 2018, 12:07:12 PM »

Got parts number you can share?


Sent from my iPhone using Tapatalk
Logged

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4808
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #6 on: May 10, 2018, 08:26:52 PM »

26600012 water pump

2670001A thermostat

32700028 coolant temperature sensor

Logged

CircleRacer

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 363
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #7 on: May 10, 2018, 10:12:22 PM »

Thank You Bob for the info and the part numbers!!
Logged

RonandJanet

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1207
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #8 on: May 12, 2018, 08:53:09 AM »

Great info thanks!
Logged

shaochieh.young

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • www.CVOHARLEY.com

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #9 on: May 12, 2018, 11:41:20 AM »

Where is the coolant sensor?  I got the same problem today.  4200 miles on a 14 CVO.


Sent from my iPhone using Tapatalk
Logged

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #10 on: May 12, 2018, 04:05:57 PM »

Where is the coolant sensor?  I got the same problem today.  4200 miles on a 14 CVO.


Sent from my iPhone using Tapatalk

See attached diagram >

Jerry
Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

shaochieh.young

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • www.CVOHARLEY.com

2014 Limited Check engine light, red temperature light P1019
« Reply #11 on: May 12, 2018, 04:22:38 PM »

Appreciated!!!!  Now is happy hunting the true problem.  I am pulling the water pump cover off to see if the pump is spinning or not.  Coolant temp was 80f and ET was 273f.  So a sensor is bad or pump is not working.


Sent from my iPhone using Tapatalk
Logged

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4808
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #12 on: May 12, 2018, 05:42:43 PM »

 Roll throttle to 1/2 , turn ignition on, and both fans and pump should come on. If the pump is pumping both radiators and hoses should feel warm or hot at operating temperature.  If radiators are cold pump could be running but not pumping.  For me the water pump was easier to replace than sensor.  This pump is made by Bosch I believe and they have pumps that look like this one but are plumbed different. They pump coolant to turbos or heaters and the like on cars and are less than $100. 😩
Logged

shaochieh.young

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • www.CVOHARLEY.com

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #13 on: May 12, 2018, 06:02:25 PM »

I think I will take the pump apart to see if it spins first and clean it then put it back.  I done the test with ignition on and I felt the vibration from the pump but I was not sure it was working or not.  I wish I was in the states right now so I could gone to HD and get my parts to fix it.  Now I have to wait on the German shop on Monday or mail order them from the states.


Sent from my iPhone using Tapatalk
Logged

Para Bellum

  • Si vis pacem, para bellum.
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1943

    • CVO1: '07 Canyon Copper FXSTSSE, '08 Crystal Copper SEUC
    • CVO2: '11 Slate/Blk SERGU, '18 Twisted Cherry RGU
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #14 on: May 14, 2018, 03:15:49 AM »

Check out this Bosch pump.  Looks amazingly similar except for the electrical plug location.  $67 from Amazon, compared to $400+ from HD:

https://www.amazon.com/Bosch-392020024-Electric-Water-Pump/dp/B001CO17V4
Logged
If you want peace, prepare for war.

shaochieh.young

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • www.CVOHARLEY.com

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #15 on: May 19, 2018, 03:39:18 PM »

The magnet cracked on the inside and no way to repair this one.  Got a new one on the way.


Sent from my iPhone using Tapatalk
Logged

RonandJanet

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1207
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #16 on: May 20, 2018, 12:18:04 PM »

I know that sucks.  Gald you found the problem. How long does it take for you get parts?
Logged

shaochieh.young

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • www.CVOHARLEY.com

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #17 on: May 20, 2018, 12:29:26 PM »

Hope this week.  Takes 5-7 days from the states to Germany.


Sent from my iPhone using Tapatalk
Logged

RonandJanet

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1207
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #18 on: May 21, 2018, 10:07:17 PM »

Well that isn't as bad as I thought it may be.  Hopefully in less time!
Logged

fos41

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 199
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #19 on: July 02, 2019, 08:43:42 AM »

Hello all have a `15 S.E.S.G. with similar symptoms check engine light on and the temp. light is on on the right. Dumb question here how can you tell, if the water pump is running cooling fans run as described in this  post, but cannot be sure pump is running or not b/c of the fan noise.
Logged

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4808
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #20 on: July 02, 2019, 04:21:18 PM »

Remove the chrome cover and put your hand on the pump and you can feel the pump running. Hope this helps.
Logged

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #21 on: July 02, 2019, 05:43:06 PM »


Depending on what actually failed (pump motor or the impeller drive), just feeling for motor vibration may not tell you what you need to know.  You need to verify that coolant is actually flowing.

Jerry
Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4808
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #22 on: July 02, 2019, 06:06:49 PM »

Depending on what actually failed (pump motor or the impeller drive), just feeling for motor vibration may not tell you what you need to know.  You need to verify that coolant is actually flowing.

Jerry

Yes as Jerry stated it will tell you if running but not pumping.  I took old one a part but saw nothing wrong but doing ok now since replacing.   Knock wood.  Sad thing is I’ll be doing again as I still have the old style pump.  Sumbitches wouldnt release new pump til old stock was depleted.  Same thing with compensators a few year ago.   :soapbox:
Logged

fos41

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 199
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #23 on: July 03, 2019, 06:40:11 PM »

Does anyone know how to find a wiring schematic for the pump and fans online I do not have a service manual. Bought a new temp switch installed, pulled water pump to visually test it`s operation, fans and pump ran for a second w/ switch on and throttle rolled open then stopped and neither fan(s) or pump works don`t you love a mystery. Any input appreciated i`m at a lost.
Logged

grc

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 14216
  • AKA Grouchy Old Fart
    • IN


    • CVO1: 2005 SEEG2
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #24 on: July 04, 2019, 09:22:41 AM »

See if the attachment helps.

Jerry

I forgot to mark the temp sensor - it's called the ECT and it's shown next to the left cooling fan.
« Last Edit: July 04, 2019, 09:27:14 AM by grc »
Logged
Jerry - 2005 Cherry SEEG  -  Member # 1155

H-D and me  -  a classic love / hate relationship.  Current score:  love 40, hate 50, bewildered 10.

fos41

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 199
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #25 on: July 04, 2019, 10:06:07 AM »

Thank you Jerry.
Logged

fos41

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 199
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #26 on: July 05, 2019, 01:13:08 PM »

Figured some things out on my water pump debacle yesterday after removing pump, it and fans ran for only a second. Discovered blown fan fuse tried one more fuse and immediate blew again when turning on switch-opening throttle attempting to turn fans on, I disconnected pump wire and eliminated the dead short caused by the pump.

Had the same code others mentioned here P1019 and P1691 & 1693 I induced when disconnecting fans testing. How do you clear the trouble codes?

$377.00 later have a new updated water pump kit hope it is a fairly straight forward installation. Thank you guys for all of your input here.

Donnie













Logged

CircleRacer

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 363
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #27 on: July 05, 2019, 01:47:06 PM »

Not at all hard to install completed changing my last week

Sent from my moto z3 using Tapatalk

Logged

shaochieh.young

  • Newbie
  • *
  • Offline Offline
  • Posts: 26
  • www.CVOHARLEY.com

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #28 on: July 06, 2019, 02:37:01 AM »

Not at all hard to install completed changing my last week

Sent from my moto z3 using Tapatalk
Dose the lower faring needs to come off?


Sent from my iPhone using Tapatalk
Logged

CircleRacer

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 363
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #29 on: July 06, 2019, 05:15:18 AM »

Yes both lowers have to come off because you have to change the hoses that connect to the bottom of both left and right radiators.

Sent from my moto z3 using Tapatalk

Logged

fos41

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 199
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #30 on: July 07, 2019, 08:32:29 AM »

Finished the install with the updated water pump kit yesterday also replaced the coolant temperature sensor for an additional preventive measure Circle Racer you right was not too bad of job.

Most time consuming part was routing the hoses and had a bit of trouble bleeding the air from the cooling system, cleared the trouble codes and put 70 miles on it with no further issues. Thank you again for all of the help I received here!


Donnie
Logged

Cheats

  • Newbie
  • *
  • Offline Offline
  • Posts: 1
  • www.CVOHARLEY.com

Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #31 on: June 12, 2022, 11:58:43 PM »

I've had this problem of the ECL Light and Temp display light come up.
Is it safe to ride the bike to my workshop - about 80kms/50mi?
Or should I put it on a trailer?
Thanks in advance
Logged

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4808
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: 2014 Limited Check engine light, red temperature light P1019
« Reply #32 on: June 13, 2022, 08:14:53 AM »

Probably everyone will give you a different answer but I would ride it. 
Logged
Pages: 1 2 3 [All]
 

Page created in 0.179 seconds with 24 queries.