Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: SE Turn Signal Module  (Read 1508 times)

0 Members and 1 Guest are viewing this topic.

iceesceu5

  • Newbie
  • *
  • Offline Offline
  • Posts: 8
  • 2010 SE Ultra / Scarlet Red & Black
SE Turn Signal Module
« on: May 01, 2013, 01:50:33 PM »

Has anyone used the SE Ultra Tour-Pak turn signal module from ride time technology? Thinking about ordering but would like to hear from those that have used the product good---or bad. Thanks





















Logged

Vyscera

  • Angsty Youth
  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 213

    • CVO1: 2010 FXDFSE2- Taken out by a Ford
    • CVO2: 2012 FLHXSE3
Re: SE Turn Signal Module
« Reply #1 on: May 01, 2013, 01:58:43 PM »

I bought a TP second hand and went through Ride time for a Y-harness. Excellent customer service, clean harness, and quick turn around. If all their work is as good, you cant go wrong.
Logged
Motorbreath is how I live my life, I cant take it any other way...

JoeVibe

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1508
    • TN


    • CVO1: 2022 CVO Road Glide Limited
    • CVO2: 2014 Titanium/Black FLHRSE6
Re: SE Turn Signal Module
« Reply #2 on: May 01, 2013, 02:10:51 PM »

I bought both Ride time harnesses (to make the corner lights and side marker lights work as turn signals) and I'm very happy with their products and the results. The install was pretty straight forward, the instructions were well written, and my back lights really get attention on the road.
« Last Edit: May 01, 2013, 05:57:44 PM by JoeVibe »
Logged

iceesceu5

  • Newbie
  • *
  • Offline Offline
  • Posts: 8
  • 2010 SE Ultra / Scarlet Red & Black
Re: SE Turn Signal Module
« Reply #3 on: May 02, 2013, 10:26:53 AM »

Thanks, I got em ordered last night. Looking forward to some added visibility.
Logged

1abastarsmda

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 3403
    • PA

    • CVO1: 2021 CVO Limited
Re: SE Turn Signal Module
« Reply #4 on: May 03, 2013, 01:42:33 AM »

I had them on my last bike and there were a must have on this one.  The guys I ride with put them on theirs too.  Excellent addition to your bike.  I did the side lights on the tourpak to blink as turn signals also.  The hardest part installing them is putting the rubber bushing back in where you run the wires into the tourpak.  After doing a few of them, even that got easier.
Logged

JoeVibe

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1508
    • TN


    • CVO1: 2022 CVO Road Glide Limited
    • CVO2: 2014 Titanium/Black FLHRSE6
Re: SE Turn Signal Module
« Reply #5 on: May 03, 2013, 07:59:48 PM »

I tried to get the connector through the hole without taking the grommet out and couldn't get it done so I pulled it out and ran the wires. Then I used a little WD-40 on the grommet and it went right back in place.
Logged
 

Page created in 0.127 seconds with 21 queries.