www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: CUSE4 Wont start after handlebars replaced  (Read 1320 times)

0 Members and 1 Guest are viewing this topic.

chrisCVO

  • ChrisCVO
  • Newbie
  • *
  • Offline Offline
  • Posts: 39
    • WV

    • CVO1: 2009 FLHTCUSE4
    • CVO2: 2020 FLHTKSE
CUSE4 Wont start after handlebars replaced
« on: May 17, 2009, 06:17:19 PM »
     After I put on new Klockwerk Ergo back bars my CUSE4 will not start!   I did not disconect the battery or pull the fuse.  (probably a mistake!)    Everything works but wont start.  Checked the fuses.   Does it have something to do with the security.   Searching for suggestions.  Thanks, Chris
Logged

Bojiboy

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 667
  • FLHRSEI.ORG

    • CVO1: 2012 FLHTCUSE7 Wicked Sapphire and Stardust Silver
Re: CUSE4 Wont start after handlebars replaced
« Reply #1 on: May 17, 2009, 08:50:09 PM »
How about the kill switch wiring? Do you hear the fuel pump run for a few seconds after you turn the key on? Just a thought.
Logged
2012 FLHTCUSE7 Wicked Sapphire and Stardust Silver
2006 FLHTCUSE (traded in)
2005 FLHRCI (sold)
Single enclosed trailer

TimBone

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 794
Re: CUSE4 Wont start after handlebars replaced
« Reply #2 on: May 17, 2009, 09:01:10 PM »
Is it in neutral?  Try all the basic stuff, you may surprise yourself!
Logged

chrisCVO

  • ChrisCVO
  • Newbie
  • *
  • Offline Offline
  • Posts: 39
    • WV

    • CVO1: 2009 FLHTCUSE4
    • CVO2: 2020 FLHTKSE
Re: CUSE4 Wont start after handlebars replaced
« Reply #3 on: May 17, 2009, 09:04:42 PM »
I put an ohm meter on the on/off switch , and the start switch. Wires are good to the deutch connector. Not sure what needs done with the security. The alarm only goes on when the bob is out of range. Alarm does not go on when bob is close. I pulled the maxi fuse hoping it would reset. No luck. Maybe try disconecting battery to see if it resets????
Its been a long day in the garage. I really like the way the bars look and feel.
I just sent my camera back to Olympus for repair. (sorry no pictures)
Was able to use stock cables. This was a big selling factor.
I got the Ergo bars dirrect from Klockwerks about a month ago.
Thanks. Chris
Logged

AXIL

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 2579
Re: CUSE4 Wont start after handlebars replaced
« Reply #4 on: May 18, 2009, 07:26:19 AM »
   just a thought, did you change the (clutch) levers? if so does the new one have the tag to push switch in the
 left housing. i see this from time to time and thought it mite help.       axil
Logged
I CAME INTO THIS WORLD WITH NOTHING AND I GOT MOST OF IT LEFT  
AHH,MOONSHINE THE OTHER WHITE MEAT

chrisCVO

  • ChrisCVO
  • Newbie
  • *
  • Offline Offline
  • Posts: 39
    • WV

    • CVO1: 2009 FLHTCUSE4
    • CVO2: 2020 FLHTKSE
Re: CUSE4 Wont start after handlebars replaced
« Reply #5 on: May 19, 2009, 08:28:41 AM »
UPDATE:    Had a loose wire going into the deutch connector from the kill switch.  (found it with volt meter)  Now I can enjoy the new bars.  Thanks, Chris
Logged

guppytrash

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1537
Re: CUSE4 Wont start after handlebars replaced
« Reply #6 on: June 15, 2009, 05:42:58 PM »
I am looking to bring the bars closer to me.  Can you post a picture of your new bars?
Thanks
Logged

chrisCVO

  • ChrisCVO
  • Newbie
  • *
  • Offline Offline
  • Posts: 39
    • WV

    • CVO1: 2009 FLHTCUSE4
    • CVO2: 2020 FLHTKSE
Re: CUSE4 Wont start after handlebars replaced
« Reply #7 on: June 15, 2009, 08:14:52 PM »
     Bike is in the shop!!!    I was 600 miles from home when I heard a loud squeal from the rear cylinder area.  I drove it home and put it into the shop.  Hope to know something this week.  Bike has 14,000 total miles on it.  Service manager said " That don't sound good" 
      I really like the bars.  Was not able to re-use the heated grips.  The inside diameter on the bars  is smaller than stock , so the heating element would not slip inside.  All stock cables work fine.   Sorry that I don't have any pictures to share at this time.  Chris
Logged

sadunbar

  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 11416
  • EBCM # Stealth - SSBS # 1.1 - SoA # Z&E2525 .01%
    • IL


    • CVO1: 2007 FLHTCUSE2
    • CVO2: 2000 FXR4
Re: CUSE4 Wont start after handlebars replaced
« Reply #8 on: June 15, 2009, 08:17:56 PM »
Quote from: cohcdt on June 15, 2009, 08:14:52 PM
     Bike is in the shop!!!    I was 600 miles from home when I heard a loud squeal from the rear cylinder area.  I drove it home and put it into the shop.  Hope to know something this week.  Bike has 14,000 total miles on it.  Service manager said " That don't sound good" 
      I really like the bars.  Was not able to re-use the heated grips.  The inside diameter on the bars  is smaller than stock , so the heating element would not slip inside.  All stock cables work fine.   Sorry that I don't have any pictures to share at this time.  Chris

Heat Demons will work in your bars...  And they have a better track record for long life than the MOCO heated grips...   :2vrolijk_21:

http://www.heatdemons.com/
Logged
2007 Screamin Eagle Ultra Classic - Light Candy Cherry and Black Ice
Screamin Eagle 120r
Revolution Performance EMS
Fuel Moto Jackpot headpipes and 4.5" Pro Touring Mufflers
HPI 55mm Throttle Body w/5.3 injectors
BDL clutch w/VPC92T
Traxxion AK-20
Legend Air Suspension
Brembo Brake Calipers/Rotors
Garmin Zumo
575 Chubby's
Bushtec Quantum

guppytrash

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1537
Re: CUSE4 Wont start after handlebars replaced
« Reply #9 on: June 15, 2009, 11:34:38 PM »
Chris
Thanks for the quick reply...I hope you get your bike back soon.  Good luck
guppytrash
Logged
 

Page created in 0.161 seconds with 25 queries.