www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Andrews 26  (Read 2239 times)

0 Members and 1 Guest are viewing this topic.

johnnymap

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 467
  • FLHTCUSE5

    • CVO1: 2010 Burnt Amber/Citrus
    • CVO2: 2005 SEEG Two Tone Red
    • CVO3: 2000 SERG BWO
Andrews 26
« on: January 23, 2010, 10:52:55 AM »
I am going to the '06 upgrade, plate, oil pump, tensioners, chains and bearings.  I was talking to my indy and he recommended putting the Andrews 26 cams.  He  said it would not require any headwork.  We are putting in adj pushrods and new lifters.  Not looking for high speed just reliability.  Don't know anything about the 26's and don't see them referenced here, that I know. of.

Doing this to my 2000 SERG.

Any comments or suggestions, would be appreciated.

Thanks,

john
Logged
"The past is a place to be remembered, but not a place to dwell"

hdbrad03

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2097
  • FLHRSEI.ORG

    • CVO1: 2009 FLTRSE3 Yellow Pearl/Charcoal Slate
    • CVO2: FLHTCSE-Pumpkin
    • CVO3: FLTRI 06
Re: Andrews 26
« Reply #1 on: January 23, 2010, 01:16:35 PM »
I had that cam in my 01 Ultra and it had great performance.


 :bananarock: :bananarock:
     Brad
Logged
I was there.  Were you?

East Coast
New River Gorge (10, 15)
Rib Fest (10, 11, 14, 15)
Wild WV (16)
Maggie Valley (08, 09, 10, 11, 12, 13, 14, 15, 16, 17)

West Coast
Sedona, AZ (08)
Pala (10)
Santa Fe, NM (13)

johnnymap

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 467
  • FLHTCUSE5

    • CVO1: 2010 Burnt Amber/Citrus
    • CVO2: 2005 SEEG Two Tone Red
    • CVO3: 2000 SERG BWO
Re: Andrews 26
« Reply #2 on: January 23, 2010, 03:40:30 PM »
Thanks, Brad.

My guy says he has great results in the baggers that he has put them in.

john
Logged
"The past is a place to be remembered, but not a place to dwell"

nidan

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1416
  • Keep the breeze between your knees

    • CVO1: 02 FWDWG3 Stage IV 95 -sold
Re: Andrews 26
« Reply #3 on: January 24, 2010, 08:11:13 AM »
The 26 has been a popular bagger cam, not much more lift than stock 06, more overlap lets it run cooler

Andrews TW26H

              Lift  Open BTDC  Close ABDC  Dur.  Overlap  Lobe Center  Lobe Sep  Lift TDC       
 
Intake     .490      11.0     35.0          226.0   20.0       102.0       104.0      .138
Exhaust   .490      41.0      9.0           230.0               106.0                    .112



Stock O6 HD inj.

       Lift  Open BTDC  Close ABDC   Dur.      Overlap  Lobe Center  Lobe Sep  Lift TDC       
 
Intake .474    -3.5         40.0       216.5     -5.0         111.8         111.5       .087
Exhaust .474    41.0       -1.5       219.5                   111.3                       .110
Logged
CVO -'02 FWDWG3 Stage IV 95 -sold
'07 FLHX Stage II 103 95hp/111lbs ft
'09 FJR 1300- 145hp /99 lbs ft
2011 Mustang GT 412hp/390 lbs ft

Razar

  • Newbie
  • *
  • Offline Offline
  • Posts: 4
Re: Andrews 26
« Reply #4 on: January 24, 2010, 08:53:47 AM »
I have the TW26a in my 03 RK.  Good improvement over stock, better roll on, mpg stayed the same. Dyno 73 hp 89 tq.  Cam comes on 2000 - 4500 rpm, right where I use it.
Razar
Logged

johnnymap

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 467
  • FLHTCUSE5

    • CVO1: 2010 Burnt Amber/Citrus
    • CVO2: 2005 SEEG Two Tone Red
    • CVO3: 2000 SERG BWO
Re: Andrews 26
« Reply #5 on: January 24, 2010, 11:46:31 AM »
Thanks, Nidan.

I believe that is what I am looking for. 

john
Logged
"The past is a place to be remembered, but not a place to dwell"

x52gnr

  • Newbie
  • *
  • Offline Offline
  • Posts: 16
Re: Andrews 26
« Reply #6 on: January 24, 2010, 04:43:37 PM »
I have them in my 07 Ultra, have been very happy with them..... :orange:
Logged
2007 Ultra
2009 V-Rod Muscle

HILLSIDECYCLE.COM

  • Banned
  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2085
Re: Andrews 26
« Reply #7 on: January 31, 2010, 08:04:18 AM »
Very good low-mid range cams.
Don't push 'em much past 9.6 cr.
Scott
Logged

aclass

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 780

    • CVO1: FLTRSE3
Re: Andrews 26
« Reply #8 on: January 31, 2010, 09:31:15 AM »
Had them in my 06 and was extremely pleased.  Really woke the engine and the exhaust up and also had a moderate aggressive idle.
Logged

johnnymap

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 467
  • FLHTCUSE5

    • CVO1: 2010 Burnt Amber/Citrus
    • CVO2: 2005 SEEG Two Tone Red
    • CVO3: 2000 SERG BWO
Re: Andrews 26
« Reply #9 on: January 31, 2010, 10:09:41 AM »
Thanks, for everyone's comments.  I ordered the parts, including cams from Jenni last week.

john
Logged
"The past is a place to be remembered, but not a place to dwell"

JeffsHogPen

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 289

    • CVO1: 2007 FXSTSSE
    • CVO2: 2001 FLHR
Re: Andrews 26
« Reply #10 on: February 01, 2010, 10:06:30 PM »
I have this cam in my 01 Roadking. I had head work done with a 95 kit......I could tell the difference and did not compromise the  reliability. Enjoy......Jeff
Logged
Hookem¨Horns!!!!!
 

Page created in 0.229 seconds with 21 queries.