www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Mounting Zumo 660 on 2010 SEUC  (Read 1515 times)

0 Members and 1 Guest are viewing this topic.

jgthomas

  • Newbie
  • *
  • Offline Offline
  • Posts: 21
Mounting Zumo 660 on 2010 SEUC
« on: February 10, 2010, 09:34:52 PM »
Just notified my 2010 SEUC arrived at the local dealer. I took over my new Zumo 660 to have them install it on the handlebar. They called today and said that it would not work since the the SEUC had the hydraulic unit on the handlebars. Any ideas from anyone who has installed on on their bike?
Logged

Fired00d

  • Global Moderator
  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 32682
  • Orange & Black SEEG... Can it get any better?
    • VA


    • CVO1: FLHTCSE
Re: Mounting Zumo 660 on 2010 SEUC
« Reply #1 on: February 10, 2010, 09:37:05 PM »
What mount were you going to use?

 :pumpkin:
Ride Safe,
Fired00d
 :fireman:
Logged
:pumpkin: 2004 Screamin’ Eagle Electra Glide :pumpkin:
Rinehart True Duals
SE Breather
SE Race Tuner
HogTunes Speakers
Zippers 575 Gear Drive Cams
Zippers Pro-Tapered Adjustable Push Rods
Zippers Oil Pressure Bypass Shim
Feuling Oil Pump
Feuling Lifters
Zumo 550 W/Flame Caps
Lyndall Z+ Brake Pads
CVOHarley Member #1234
PGR Member #754 (Since '05)
Proud Member EBCM #2.0

citruscvoguy

  • Newbie
  • *
  • Offline Offline
  • Posts: 23

    • CVO1: 2010 SEUC Citrus
Re: Mounting Zumo 660 on 2010 SEUC
« Reply #2 on: February 10, 2010, 11:00:13 PM »
Quote from: jgthomas on February 10, 2010, 09:34:52 PM
Just notified my 2010 SEUC arrived at the local dealer. I took over my new Zumo 660 to have them install it on the handlebar. They called today and said that it would not work since the the SEUC had the hydraulic unit on the handlebars. Any ideas from anyone who has installed on on their bike?
HMM, I just installed mine on my 2010 SEUC and it fits perfect with the HD mount. Took me 30 minutes with the instructions with the HD mount kit. 
For a easy power source just run the power wire in thru were the handlebar goes into the fairing and pop out the headlight. You'll see the capped off wires for the ultra fender light taped to the wiring harness. Just connect them and you have power for your zumo switched to the ignition... Hope this helps
Logged

wenchal

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 413

    • CVO1: 2012 FLTRU
    • CVO2: 2008 SEUC - SOLD
Re: Mounting Zumo 660 on 2010 SEUC
« Reply #3 on: February 11, 2010, 08:07:58 AM »
Ditto, I'm using the HD mount and works fine. 
Logged

skreminegul07

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2446
  • FLHRSEI.ORG
    • MA


    • CVO1: 2017 Indian Chieftain Limited
Re: Mounting Zumo 660 on 2010 SEUC
« Reply #4 on: February 11, 2010, 10:20:29 AM »
Quote from: jgthomas on February 10, 2010, 09:34:52 PM
Just notified my 2010 SEUC arrived at the local dealer. I took over my new Zumo 660 to have them install it on the handlebar. They called today and said that it would not work since the the SEUC had the hydraulic unit on the handlebars. Any ideas from anyone who has installed on on their bike?
The instructions said that there were two different sets of spacers in the kit, one for hydraulic clutch, one for cable.
Logged
Any day on the bike is a good day.

Boatman

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4816
  • FLHRSEI.ORG

    • CVO1: 2014 CVO Limited
    • CVO2: 2010 SEUC-accident victim-gone
    • CVO3: 2005 SEEG-traded on 2010
Re: Mounting Zumo 660 on 2010 SEUC
« Reply #5 on: February 11, 2010, 12:16:04 PM »
Quote from: skreminegul07 on February 11, 2010, 10:20:29 AM
The instructions said that there were two different sets of spacers in the kit, one for hydraulic clutch, one for cable.

What the heck are instructions?       :)

(Glad someone else reads them besides me)..    :2vrolijk_21:
Logged
 

Page created in 0.217 seconds with 21 queries.