www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Help from anyone with the Ultracool oil cooler.  (Read 1305 times)

0 Members and 1 Guest are viewing this topic.

bubtrauma

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 951
Help from anyone with the Ultracool oil cooler.
« on: July 18, 2011, 10:15:12 AM »
Sorry if I put this in the wrong place but I need help with my install.

I am having trouble with the reroute of the clutch cable. If I put it behind the down tubes it is going to be very close to the new motor mount on the top of the engine.

What to do.....?

Bub
Logged
bend it, chop it, cut it, bang it, weld it and paint it to match........

cvobiker

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 2643
Re: Help from anyone with the Ultracool oil cooler.
« Reply #1 on: July 18, 2011, 09:52:48 PM »
Quote from: bubtrauma on July 18, 2011, 10:15:12 AM
Sorry if I put this in the wrong place but I need help with my install.

I am having trouble with the reroute of the clutch cable. If I put it behind the down tubes it is going to be very close to the new motor mount on the top of the engine.

What to do.....?

Bub

I helped a freiend install one beginning summer and trust me the cable works fine relocated behind the down tubes,,, follow the instructions, apply the tie wrap through the little hole on the cross brace, it's there, just look for it.. Do this and you wont have any interference problems with the top motor mount.. Also make sure to cut the tie wraps supporting the clutch cable inside the faring to allow more slack, which you will need.

good luck.. 
Logged

bubtrauma

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 951
Re: Help from anyone with the Ultracool oil cooler.
« Reply #2 on: July 18, 2011, 10:59:00 PM »
Well I aint happy the instructions suck............there is no instuctions for wiring the thermastat,

shi,,,,,,,,,,,,,,,,,
Logged
bend it, chop it, cut it, bang it, weld it and paint it to match........

cvobiker

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 2643
Re: Help from anyone with the Ultracool oil cooler.
« Reply #3 on: July 19, 2011, 01:17:29 AM »
Quote from: bubtrauma on July 18, 2011, 10:59:00 PM
Well I aint happy the instructions suck............there is no instuctions for wiring the thermastat,

shi,,,,,,,,,,,,,,,,,

I remember a clear set of instructions, you may want to contact Ultracool and ask them to email you a PDF copy.. Where did you purchase from? It's very simple though,  I recall red wire going too accessory switch, black to ground and that's it...The thermostat is self contained and does not require power, it simply regulates oil flow based on temperature.
« Last Edit: July 19, 2011, 01:25:16 AM by cvobiker »
Logged

bubtrauma

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 951
Re: Help from anyone with the Ultracool oil cooler.
« Reply #4 on: July 19, 2011, 09:13:38 AM »
there is a separate thermostat that goes in a hole beside the oil drain plug or something

I wish I would have never bought this .......thing.
Logged
bend it, chop it, cut it, bang it, weld it and paint it to match........

Midnight Rider

  • AKA: TCnBham
  • 10K CVO Member
  • ****
  • Offline Offline
  • Posts: 11107
  • FLHRSEI.ORG

    • CVO1: 2011 SERGU Rio Red (sold)
Re: Help from anyone with the Ultracool oil cooler.
« Reply #5 on: July 19, 2011, 10:15:33 AM »
Quote from: bubtrauma on July 19, 2011, 09:13:38 AM
there is a separate thermostat that goes in a hole beside the oil drain plug or something

I wish I would have never bought this .......thing.

I'm just guessing, but that's probably a sensor for the fan operation.
Logged
Sometimes it takes a whole tankful of fuel before you can think straight.
I had the right to remain silent, just not the ability...

Gone, but not forgotten...2011 FLTRUSE with
Fullsac X Pipe w/2" Baffles
Legend Air Ride Rear Shocks
Traxxion Dynamics AK-20 Front Suspension
Clearview GT13 Windshield
TTS Mastertune

hotroadking

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 192
Re: Help from anyone with the Ultracool oil cooler.
« Reply #6 on: July 19, 2011, 10:27:28 AM »
Or you could simply google Ultra Cool and go to the install page on their web
site and download the pdf and look at the pictures of the install to get
the information you need.

Ultra Cool Install Page
Logged
"My rule of life prescribed as an absolutely sacred rite smoking cigars and also the drinking of alcohol before, after and if need be during all meals and in the intervals between them." Winston Churchill

bubtrauma

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 951
Re: Help from anyone with the Ultracool oil cooler.
« Reply #7 on: July 19, 2011, 12:01:08 PM »
Well ..... Here is what happened. I purchased this cooler from a company in Canada which since went bankrupt. Nothing was right even the plastic shroud doesnt fit. So..... I called Robert from the Company and he was not happy and said he will send me all the right stuff.

Now I am happier

Thanx Guys

This Company "Ultracool" has GOOD costomer SERVICE.

Bob
Logged
bend it, chop it, cut it, bang it, weld it and paint it to match........

timtoolman

  • never enough torque!!!!!!!
  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 447

    • CVO1: Hillside Stg 4 117, S&S 66 T.B. Woods 400-6, Rush 2-1 Wrath
Re: Help from anyone with the Ultracool oil cooler.
« Reply #8 on: July 20, 2011, 11:57:00 PM »
Talked to robert a ultra cool and he said a new improved bigger cooler will be out in about a month from now. Its for bigger hp engines
Logged
 

Page created in 0.23 seconds with 25 queries.