www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Kuryakyn TC-24D Cams  (Read 2472 times)

0 Members and 1 Guest are viewing this topic.

schok

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
  • 2009 CVO
Kuryakyn TC-24D Cams
« on: October 10, 2013, 09:53:27 PM »
I've been waiting to see more comments and dyno sheets as more members install these cams but there doesn't seem to be any new info. Has anyone other than Bowtech installed this cam?
Logged
You can learn something new every day.........if you start off stupid enough!

TorqueInc

  • Get your facts first, then you can distort them as you please. Mark Twain
  • Vendor
  • Senior CVO Member
  • *
  • Offline Offline
  • Posts: 391
Re: Kuryakyn TC-24D Cams
« Reply #1 on: October 10, 2013, 10:43:32 PM »
  Local pres has one on here somewhere
Logged
2011 SG Sedona Orange 105" 125/123

www.jwperf.com

chicoman

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 75
Re: Kuryakyn TC-24D Cams
« Reply #2 on: October 11, 2013, 08:11:30 AM »
Did all bore 113 from suburban hd, wfo larry heads, kury 57mm tb, supertrap. Cut dome down on pistons to get 10.1 to 1, @190 ccp. Kury 24d cam, runs great pulls everywhere, 40 plus mpg. Great tune from bob at razorback in wisc.
If i were to do it again i would leave the pistons as is and pic up a few extra hp an tq. This has zero pinging in any riding conditon, Im very happy
Logged

schok

  • Newbie
  • *
  • Offline Offline
  • Posts: 11
  • 2009 CVO
Re: Kuryakyn TC-24D Cams
« Reply #3 on: October 11, 2013, 08:19:23 AM »
Chicoman, Thanks for posting your Dyno sheet. I think this is the cam for me but after the initial hubbub there was no new info coming down the line. Your numbers are great! How are you finding the heat issue / running so hot, with your bike after the mods? Schok
Logged
You can learn something new every day.........if you start off stupid enough!

DCFIREMANN

  • 2.5K CVO Member
  • **
  • Offline Offline
  • Posts: 4812
Re: Kuryakyn TC-24D Cams
« Reply #4 on: October 11, 2013, 08:31:23 AM »
I am getting ready to do almost the same build on my 2012. I am going to break the cases and plug and weld the flywheels. I am sending the heads north and I am going to run the 4.060 HD pistons with a 58 mm HD TB. Also going with a fueling cam plate, oil pump and lifters. Not looking to build a speedster just looking to make it bullet proof and a little more in the TQ range.

Be Safe

THE DAWG
Logged
cvo 1  04 FLHTCSEI  Qrange/Black AKA Ole Punkin
cvo 2 05 VRSCXe Orange/Black sold
cvo 3 02 FXDWG2 Black/Gold 
cvo 4 04 FLHTCSE Blue/Black  sold
cvo 5 09 FLHTCUSE4 Red/Marron sold
cvo 6 12 FLHTCUSE Blue Saphire/Stardust Silver AKA Saphire
cvo 7 14 FLHTKSE  Blaze/Maroon
2020 CVO Limited

PROUD MEMBER EBCM #1.75 Second in command of this great organization

Also has been placed on
TRIPLE SECRET PROBATION

chicoman

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 75
Re: Kuryakyn TC-24D Cams
« Reply #5 on: October 11, 2013, 09:19:59 AM »
No heat issue at all, the tune takes care of that. Hottest the oil temp has been in 90+ riding has been 220. Great all around touring having fun motor. Get a pipe without the cat in to get rid of the heat on your leg.
Logged

TorqueInc

  • Get your facts first, then you can distort them as you please. Mark Twain
  • Vendor
  • Senior CVO Member
  • *
  • Offline Offline
  • Posts: 391
Re: Kuryakyn TC-24D Cams
« Reply #6 on: October 13, 2013, 08:43:04 AM »
  One of the better ones ive seen...done by Sachs,where id send my heads if I didn't do them meself
Logged
2011 SG Sedona Orange 105" 125/123

www.jwperf.com
 

Page created in 0.167 seconds with 25 queries.