Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Frankiethechin]

Can I add led turn single lights without adding anything else I have a 2015 cvo street glide which has led break lights

[Ghost__Rider]

I have Kuryakyn leds on my CVO Limited, They match the Led lights on the bike great. Sure beats the heck out of the incandesant bulb turn signals.

[Ghost__Rider]

[ChopperPilot]

I put the Custom Dynamics LED turn signals on my last two bikes. Great products to pick from and great customer service.

[North Georgia Hawg]

I put the Custom Dynamics LED turn signals on my last two bikes. Great products to pick from and great customer service.

Great timing... I JUST now posted on my mods thread that I installed the Dynamic Rings from Custom Dynamics on Honey Badger today.

The Ringz are super bright. And, on the 14-later CANBUS bikes, you don't even need their load equalizer. They are the best turn signal LED products out there.

Ken

[North Georgia Hawg]

Dynamic Ringz left turn signal on...

[CVODON]

I put both frt and rear Custom Dynamics LED's in my 2015 RG CVO Ultra and added the unit to make rear turn signals into run/turn/brake. The LED's worked fine initially, but the dash indicators would fast flash, the lights were OK but the indicators were not. I talked with Megan @ Custom Dynamics who gave me a sequence to go thru and the system "learned" the load and everything was great. I do not remember what I did, but it took a couple minutes and all is good. Nothing else to add and nothing else to buy except the lights.
Been four months and they work great.

[mark]

Can I add led turn single lights without adding anything else I have a 2015 cvo street glide which has led break lights

The below tip is from Radiantz, which makes a product similar to Custom Dynamics Dynamic Ringz LEDs.

"Here is a quick test to see if you need a load equalizer. Pull out your stock front bulbs and turn on your turn signal and if the rear turn signal stays flashing at the correct rate then you will not need a load equalizer. If the rear turn signal flashes a couple of time and goes into a fast flash then you will need a load equalizer."

[GregKhougaz]

From Kuryakyn :

CAN BUS SYSTEM MODELS: IMPORTANT: Load equalizers are NOT necessary on CAN bus systems when LED Turn Signal Inserts are installed. STEP 6 Start the bike and check for proper turn signal operation. If the turn signals flash rapidly on CAN bus system bikes, you will need to synchronize the turn signal system. Follow the procedure below to synchronize: BRAKE-SIDE (RIGHT) HAZARD (4 WAYS) BUTTON ON HAND CONTROLS = CAN BUS SYSTEM Turn the ignition ON, Turn on the 4-way flashers for at least 20 seconds; shut the 4-way flashers off, Turn the ignition OFF, Turn the ignition back ON; check for proper turn signal operation, You may need to repeat the procedure if the signals still flash rapidly. NOTE: -cont.- Diagnostic Trouble Codes (DTC) may be triggered during initial startup when using LED Turn Signal Inserts. To clear the DTCs, follow the procedure on PAGE 3.

[Ghost__Rider]

From Kuryakyn :

CAN BUS SYSTEM MODELS: IMPORTANT: Load equalizers are NOT necessary on CAN bus systems when LED Turn Signal Inserts are installed. STEP 6 Start the bike and check for proper turn signal operation. If the turn signals flash rapidly on CAN bus system bikes, you will need to synchronize the turn signal system. Follow the procedure below to synchronize: BRAKE-SIDE (RIGHT) HAZARD (4 WAYS) BUTTON ON HAND CONTROLS = CAN BUS SYSTEM Turn the ignition ON, Turn on the 4-way flashers for at least 20 seconds; shut the 4-way flashers off, Turn the ignition OFF, Turn the ignition back ON; check for proper turn signal operation, You may need to repeat the procedure if the signals still flash rapidly. NOTE: -cont.- Diagnostic Trouble Codes (DTC) may be triggered during initial startup when using LED Turn Signal Inserts. To clear the DTCs, follow the procedure on PAGE 3.

Mine didn't set a code or anything. Plugged them in and they worked fine. No load equalizers or anything.

[Puma]

Great timing... I JUST now posted on my mods thread that I installed the Dynamic Rings from Custom Dynamics on Honey Badger today.

The Ringz are super bright. And, on the 14-later CANBUS bikes, you don't even need their load equalizer. They are the best turn signal LED products out there.

Ken

I did them on the CVO Road King on the front only as the rears are the led tail lights on the bag fillers. No load equalizer. Worked perfectly. And like Ken said they are hella BRIGHT.