www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: How did you run your wiring for your Garmin 660?  (Read 1357 times)

0 Members and 1 Guest are viewing this topic.

Hawg

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 855

    • CVO1: 2010 FLHXSE
How did you run your wiring for your Garmin 660?
« on: April 22, 2010, 10:13:35 PM »
Just finished installing my 660 mount and now wondering the best route for the wiring pictures would also help.
Logged
Hawg

SmileMaker

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 54

    • CVO1: FLHTCUSE3 Anniversary
    • CVO2: 97 FLSTS Blue & White
Re: How did you run your wiring for your Garmin 660?
« Reply #1 on: April 23, 2010, 03:07:29 PM »
Logged

Hawg

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 855

    • CVO1: 2010 FLHXSE
Re: How did you run your wiring for your Garmin 660?
« Reply #2 on: April 24, 2010, 06:37:39 PM »
Completed the wiring today very pleased how it turned out, ran the wire alongside the handle bar into the fairing on the left side, joined up with connections strapped to the headlight harness.
Installed heat shrink on the usb, headphone, and mic connection and black taped them to the harness should be good and water tight. The picture is your view as sitting in the saddle, notice the fuel gauge is easy to see. I used the Harley handle bar mount, sent it and the spacers in for chrome (it just didn't look good black), also needed to add three washers on the mounting screws in order to keep the GPS mounting bar away from the clutch reservoir.
« Last Edit: April 24, 2010, 06:46:10 PM by Hawg »
Logged
Hawg

Hawg

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 855

    • CVO1: 2010 FLHXSE
Re: How did you run your wiring for your Garmin 660?
« Reply #3 on: April 24, 2010, 06:54:38 PM »
side view
Logged
Hawg

Hawg

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 855

    • CVO1: 2010 FLHXSE
Re: How did you run your wiring for your Garmin 660?
« Reply #4 on: April 24, 2010, 07:07:34 PM »
notice the positioning of the hardware to position the GPS as far left as possible to enable viewing the fuel gauge
Logged
Hawg

Hawg

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 855

    • CVO1: 2010 FLHXSE
Re: How did you run your wiring for your Garmin 660?
« Reply #5 on: April 24, 2010, 07:16:11 PM »
Inside view of the fairing (borrowed pic), connected GPS power supply to the unused connectors strapped to the headlight wiring harness. (white arrow bottom of pic)
« Last Edit: April 24, 2010, 10:23:53 PM by Hawg »
Logged
Hawg

Hawg

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 855

    • CVO1: 2010 FLHXSE
Re: How did you run your wiring for your Garmin 660?
« Reply #6 on: April 24, 2010, 07:19:57 PM »
another view
Logged
Hawg

Hawg

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 855

    • CVO1: 2010 FLHXSE
Re: How did you run your wiring for your Garmin 660?
« Reply #7 on: April 24, 2010, 07:20:58 PM »
last one
Logged
Hawg
 

Page created in 0.217 seconds with 21 queries.