Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: New Handlebars and the never-ending rabbit hole  (Read 6656 times)

0 Members and 1 Guest are viewing this topic.

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
New Handlebars and the never-ending rabbit hole
« on: September 02, 2021, 01:25:06 PM »

Tore my bicep in early June, had surgery and Doc said no riding for 3 months.  Finally healed up enough to turn a wrench so I figured it would be a good time to upgrade the old SEEG. 

Front tire had a very strange wear pattern so, at Michelin's request, I took it to cycle gear and got a new MCIII (I'll report back on any vibrations once I get on the road) for the cost of mounting $25!  Might as well replace bearings while the wheel is off so ordered new bearings and bearing puller/installation tools;

I thought while I'm at it, might as well put the LA Choppers 10" Twin Peaks on.  Ditched the 2 piece clamps in favor of a 1-piece with allen set screws. Can't put new bars on without new bushings right? Ordered Drag Specialties Poly Bushings.  Bars are on and look great, so much more comfortable than stock.  I was prepared for the internal wiring to be aggravating but it only took me about 10 minutes to get them through and re-pinned.  I was able to use stock throttle cables, wiring, and hydraulic cables with some minor re-routing.  Brake line isn't banjo-string tight but definitely could not go with bars any higher;

I have the Streetglide fairing mirrors which are completely blocked by my paws with the new bars, luckily I still had the stock handlebar mirrors but had to plug the holes in the fairing so off to lowes for push-plugs (got 1" which covers both holes, painted them gloss black to match the fairing, and pulled them up tight with a nut on the back of the plug.  They look better than any other plugs I could find online and cost me less than $1);

While I've got the fairing rolled forward and I can easily torque the fork caps, might as well change the fork oil so ordered Bel-Ray 10W, and new fork cap seals.  It's hard to torque the phillips-head fork drain bolts so ordered new allen-head fork drain bolts and washers;

I'm not quite finished yet (family obligations have pulled me away several times) but everything has gone pretty smooth.  All total I'm in the rabbit hole for less than $400, not bad considering it would have probably been over $1,500 at H-D.

I'll post up some pics when I get her all buttoned up.
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #1 on: September 02, 2021, 02:06:03 PM »

Homemade fairing plugs:
Logged

ultra13

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 517
  • www.CVOHARLEY.com
    • OH


    • CVO1: 2013 CVO Ultra
Re: New Handlebars and the never-ending rabbit hole
« Reply #2 on: September 02, 2021, 06:43:14 PM »

U have been busy!!!  Can't wait to see the pics....Being that I can't fig out how to do it...lol
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #3 on: September 02, 2021, 06:51:57 PM »

It’s not hard just lots of steps which takes a long time.  My OCD wouldn’t allow me to move to the next step without rechecking the step I just did.  Should have it finished tomorrow.
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #4 on: September 04, 2021, 12:14:00 PM »

Got it finished yesterday and took it for a hot lap today, bars feel great, no vibration with Michelin Commander III, forks feel firm but absorb bumps very well.
« Last Edit: September 04, 2021, 12:20:56 PM by SIKBIRD »
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #5 on: September 04, 2021, 12:15:14 PM »

Back
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #6 on: September 04, 2021, 12:17:23 PM »

Front
Logged

ultra13

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 517
  • www.CVOHARLEY.com
    • OH


    • CVO1: 2013 CVO Ultra
Re: New Handlebars and the never-ending rabbit hole
« Reply #7 on: September 04, 2021, 12:55:48 PM »

Looks good. I like the bars at or below the fairing height. That's why I got 10's on mine.
I went with shorter stemmed mirrors because the stocks stuck up too far after I installed the bars.
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #8 on: September 04, 2021, 03:35:35 PM »

Thanks! I was concerned about the old “go 2” higher than what you think you want” but these are the perfect height for me.  My only regret is not doing it 7 years sooner.  Takes a little getting used to looking under my arms to see the mirrors but they have a much wider view than the SG mirrors.
« Last Edit: September 04, 2021, 03:37:59 PM by SIKBIRD »
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #9 on: October 08, 2021, 08:10:20 PM »

After carefully examining my Bird, I decided the mirrors just weren’t going to cut it so I found some low-profile Arlen Ness knockoffs on eBay.  They have a surprisingly good view considering how small they are.
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #10 on: October 08, 2021, 08:11:41 PM »

Another angle
Logged

SIKBIRD

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 652
  • www.CVOHARLEY.com
    • AL


    • CVO1: 2004 FLHTCSE: Orange Pearl & Jet Black
Re: New Handlebars and the never-ending rabbit hole
« Reply #11 on: October 08, 2021, 08:13:35 PM »

Last
Logged

ultra13

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 517
  • www.CVOHARLEY.com
    • OH


    • CVO1: 2013 CVO Ultra
Re: New Handlebars and the never-ending rabbit hole
« Reply #12 on: October 11, 2021, 09:09:43 PM »

Now that is different... 8)
Logged
 

Page created in 0.232 seconds with 24 queries.