Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Fired00d]

I just purchase a "used" HD LED bar on eBay. Everything seems to be included except for the installation instructions.  Have been searching the Internet with no luck on finding a copy of the. 


Does anyone have a copy of the installation instructions or a step-by-step install?

What is the P/N and have you checked the MoCo website? They have instructions online for a lot of parts now.

 
Ride Safe,
Fired00d
 

[Joram]

P/N is 57335-08 and I checked the MoCo website..  The give no download for the install directions 

I am sure hoping someone on the forum can help.. Don't want to spend $80/hour for local Stealer to do it, as I have to drive 86 miles to get to them.

[Fired00d]

Just did a search and found one thread - Illuminated Windshield Molding where a member has (was asking for help) installed this accessory. The original poster hasn't been on in awhile, but the member that replied first is on quite a bit. If he doesn't see your thread you might send him a PM.

 
Ride Safe,
Fired00d
 

[Joram]

Looked at the post and did not find a lot of help 

a quote from the thread

Follow the instructions to the tee, you will not have a problem.

Could be helpfull if ONLY I had the directions. 

[Fired00d]

Looked at the post and did not find a lot of help 

a quote from the thread

Could be helpfull if ONLY I had the directions. 

That's why I was saying the member that replied first (the one you quoted) might be able to help you sounds like he's either done it or knows about it. Hopefully he'll see this thread and reply if he doesn't send him a PM he might have the instructions or know of someone that does.

 
Ride Safe,
Fired00d
 

[Joram]

Ahh..  got it now..  Thanks 

[Heatwave]

I have the HD LED fairing molding http://www.harley-davidson.com/gma/gma_product.jsp?PRODUCT%3C%3Eprd_id=845524448771262&FOLDER%3C%3Efolder_id=2534374302290631&ASSORTMENT%3C%3East_id=2534374302290631&bmUID=1273685717568&bmLocale=en_US . I installed it myself. The drilling isn't that big of a deal. Pretty simple actually. The bigger challenge is getting all of the pins into the correct connectors in the right locations. It can appear somewhat daunting at first but if you take your time and match all the colors of the wiring it's actually not that difficult.

I also have the BAL S3 - LED tailight and have no issues with the LED moulding or the built-in led turn signals. I am planning to swap out my incandescent turn signal bulbs to LEDs. I was planning on using the BadLands 8-pin Illuminator module ILL-01-A (Run/Turn/Stop + Load Equalizer) with Red Radiantz LEDS (LED-DR56) in the rear and Amber Radiantz LEDs up front (LED-DA57).

Any reason why this combo might not work or a better setup for LED turn signals on a 2010 SE Ultra? I'm hoping with the Badlands Illuminator module I'll have no issues with the Security System, normal turn signal operation, 4 way flashers or heat issues from the module. Am I missing anything?

[hafbad0]

Ahh..  got it now..  Thanks 

Joram, just getting a chance to check my email.  Sorry about the late reply but, I see that you things rolling.  Post a pic of the finish work.

Milford 

[Fired00d]

I have the HD LED fairing molding http://www.harley-davidson.com/gma/gma_product.jsp?PRODUCT%3C%3Eprd_id=845524448771262&FOLDER%3C%3Efolder_id=2534374302290631&ASSORTMENT%3C%3East_id=2534374302290631&bmUID=1273685717568&bmLocale=en_US . I installed it myself. .....

The OP needs the directions can you scan/post them for him??

 
Ride Safe,
Fired00d
 

[Heatwave]

The OP needs the directions can you scan/post them for him??

 
Ride Safe,
Fired00d
 

I'll check this evening and see if I still have them.

[Fired00d]

I'll check this evening and see if I still have them.

Thanks.

 
Ride Safe,
Fired00d
 

[Joram]

Thanks HEATWAVE 

If the file is to big to post, PM me and I will send you my email.

[Heatwave]

I found the instructions and scanned them but the file is 4400kb (too big to post). I'll try to send you a PM with the file. If it's too big to send via PM I'll need your email address. Let me know if you have any questions. Hopefully you're handy with wiring because as I said.... getting all the pins in the right connectors will appear daunting until you get into it. Good luck.

[Joram]

Thanks HEATWAVE 

Got the directions in my inbox this morning.. Soon as my new LED lights for the gauges come in, I am off to install this all.