www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Fender extention to prevent engine grime  (Read 2553 times)

0 Members and 1 Guest are viewing this topic.

Randylee

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 127
  • RN; USAF Medic ('97-present); USMC ('88-'92)

    • CVO1: FXDFSE - Fat Bob (Black & Fire Quartz)
    • CVO2: aka 2002 Yamaha V-max (commuter bike)
    • CVO3: aka 2008 XL1200L (wife's Sportster)
Fender extention to prevent engine grime
« on: July 28, 2010, 02:29:41 AM »
With only a few hundred miles on my FXDFSE, I had apparently ridden through some recent road construction where my front tire picked up some asphalt particles that stuck EVERWHERE bike was heated up - cooling fins, casing, all along pipes, everywhere.  I did a lot of searching to find best way to get it off.  I wanted to avoid any wiping - needed something to disolve the asphalt, gentle enough to preserve engine paint/coating and also wash off without leaving residue.  I finally settled on WD-40.  It worked great using just a soft toothbrush and my fingers and a lot of patience.  

To prevent this I looked for a front Fender Extention.  MoCo sells a chrome extention for Dynas (Part No 59664-03) but it doesn't fit Fat Bobs.  I found and ordered a front fender flap from Timberwolfleather.com.  I'm really happy with it.  Thought I'd share in case any of you had similar issue.  Picture below.
« Last Edit: October 24, 2010, 01:39:34 AM by Randylee »
Logged

Randylee

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 127
  • RN; USAF Medic ('97-present); USMC ('88-'92)

    • CVO1: FXDFSE - Fat Bob (Black & Fire Quartz)
    • CVO2: aka 2002 Yamaha V-max (commuter bike)
    • CVO3: aka 2008 XL1200L (wife's Sportster)
Re: Fender extention to prevent engine grime
« Reply #1 on: July 28, 2010, 02:38:38 AM »
The flap came with mounting hardware but I went to local hardware store and bought a shorter screw as well as a Rubber Washer to preserve paint job around the mounting hole. 
Logged

Randylee

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 127
  • RN; USAF Medic ('97-present); USMC ('88-'92)

    • CVO1: FXDFSE - Fat Bob (Black & Fire Quartz)
    • CVO2: aka 2002 Yamaha V-max (commuter bike)
    • CVO3: aka 2008 XL1200L (wife's Sportster)
Re: Fender extention to prevent engine grime
« Reply #2 on: July 28, 2010, 02:51:12 AM »
Post here if you've found another Fender Extension that works with our Fat Bobs.  Thanks.
« Last Edit: September 09, 2010, 04:53:07 AM by Randylee »
Logged

Tom of VA

  • Newbie
  • *
  • Offline Offline
  • Posts: 34
Re: Fender extention to prevent engine grime
« Reply #3 on: August 18, 2010, 05:11:26 PM »
I think I will buy one of those too.
Logged
 

Page created in 0.209 seconds with 21 queries.