Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Twolanerider]

The addition of the Feuling oil pump is a must if you plan on keeping one of these 103's for the long terms.

[Fired00d]

Cams were installed last week and dyno tune completed last Friday by Jim Brown, Braggin' Rights Dyno, who did a portion of the testing on these cams with Zippers........this installation, the 575's give the seat of the pants feeling of DOUBLE the TQ at 2500 and put the strongest pull right in the middle of the driveability range.

[The Mysterious Q!]

I'd love to see you hanging that  [smiley=pumpkin.gif] up [smiley=xyxthumbs.gif]

[Street Stalker]

It's nice to see that even with 2-2's the torque increase is still there towards the low end of the rpm scale.  My Fatboy is getting the install right now and I did a baseline run before the install and plan on doing one after.  Will post the results later in the week.

[JR]

While things were apart for the cam installation also changed the lifter blocks, pushrod tubes and rocker boxes.

[Fired00d]

Don,
Those additions look nice. [smiley=xyxthumbs.gif] However those pictures pointed something out to me, or should I saw sparked my "OCD/SEO". I had forgotten about the chrome fuel line, and was wondering if this is the part - Braided Stainless Steel EFI Fuel Line. If I remember correctly from a post somewhere this part is for Dyna's, but will work on our bikes. Looking at your picture and what MoCo website shows for the part above, looks like you have a combination of that line, and this cover Fuel Tank Fitting Cover I tried searching but couldn't come up with this information. If this is not the right parts or combination parts, can you please advise. Thanks.

 [smiley=pumpkin.gif]
Ride Safe,
Fired00d
 [smiley=fireman.gif]

Ok, I found the post Gas line revision it was in "Twin Cam" section and I searched only in the "FLHTCSE/2" section that pertained to that fuel line. I do have the right part for the line. It still looks like the fitting that connects to the tank is different on yours, then in picture of that part in online MoCo parts catalog. Are you using the additional "Fuel Tank Fitting Cover" also?


 [smiley=pumpkin.gif]
Ride Safe,
Fired00d
 [smiley=fireman.gif]

[SEULTRA]

'd00d, eat two of these: and stay close to the site until she comes home again.

Kinda like Popeye and spinach, huh??  [smiley=huepfenjump3.gif]

[spydglide]

Hey 2Lane, you said you're running about 8 degrees cooler on the rear jug temp. than before........just to get a idea of the significance of that, wonder how many degrees our oil coolers lower the temp. than if we were without them?  Any idea?   [smiley=nixweiss.gif]  spyder

[JR]

Ok, I found the post Gas line revision it was in "Twin Cam" section and I searched only in the "FLHTCSE/2" section that pertained to that fuel line. I do have the right part for the line. It still looks like the fitting that connects to the tank is different on yours, then in picture of that part in online MoCo parts catalog. Are you using the additional "Fuel Tank Fitting Cover" also?


 [smiley=pumpkin.gif]
Ride Safe,
Fired00d
 [smiley=fireman.gif]

d00d, not to be answering for Twolane but I believe he has the same one I got. It's p/n 62809-06. Here is a pic off the MOCO site.

                                                  JR [smiley=banana.gif]

[Fired00d]

d00d, not to be answering for Twolane but I believe he has the same one I got. It's p/n 62809-06. Here is a pic off the MOCO site.

                                                

[JR]

d00d,

I just have the chrome fitting cover. Had it installed when I got the bike new along some other goodies. I wasn't aware of the fuel line until later. But it may on sooner than later!

                                                                      JR [smiley=banana.gif]

[Fired00d]

I've been told that I have the knack for feeding ones "OCD/SEO". [smiley=huepfenjump3.gif]

 [smiley=pumpkin.gif]
Ride Safe,
Fired00d
 [smiley=fireman.gif]

[Twolanerider]

d00d, not to be answering for Twolane but I believe he has the same one I got. It's p/n 62809-06. Here is a pic off the MOCO site.

                                                

[Twolanerider]

Don,

I really like the look, I really didn't notice the rocker boxes before. I guess now that I calmed down a bit since my bike went to the dealer I was able to notice. Looking good bro! [smiley=xyxthumbs.gif]

                                                                   JR [smiley=banana.gif]

Thanks JR.  As a combination I really quite like the rocker boxes and lifter blocks.  The lifter blocks look a lot less bulky than the lofter block covers that were there previously too.  It was all apart anyway so if those parts were going to get hung that was the time to do it.

[Twolanerider]

Hey 2Lane, you said you're running about 8 degrees cooler on the rear jug temp. than before........just to get a idea of the significance of that, wonder how many degrees our oil coolers lower the temp. than if we were without them?