Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 2 [All]

Author Topic: Flush Mount Gas Cap Trim Ring Replacement  (Read 6334 times)

0 Members and 1 Guest are viewing this topic.

Dughr

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 65

    • CVO1: FLSTFSE '05
    • CVO2: FXSTSSE '07
Flush Mount Gas Cap Trim Ring Replacement
« on: March 06, 2012, 10:02:42 AM »

Hi,

So my newest CVO has a flawed trim ring on the gas cap side of the tank.  It looks like I can replace the trim ring with part#    63028-06.  Has anyone done this?  How did you get the trim ring off without damaging the paint?

Thanks!
Logged

Twolanerider

  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 48951
  • EBCM #1.5 Emeritus DSP # ? Critter Gawker #?
    • MO


    • CVO1: 2000 Triple Red Screamin' Eagle Road Glide
    • CVO2: 2002 Candy Brandywine Screamin' Eagle Road King
    • CVO3: 1999 Arresting Red FXR2
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #1 on: March 06, 2012, 10:20:30 AM »

It's held on with two sided tape.  You'll cut it off with fishing line or dental floss or other such non-marring device. 
Logged

CVOSE

  • Newbie
  • *
  • Offline Offline
  • Posts: 43

    • CVO1: VRSCSE2
    • CVO2: FLHTKSE
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #2 on: March 06, 2012, 11:37:35 PM »

Don't worry how to get it off. Worry how to leave it on. It came of my tank two times, the glue is not fuel resistant. Once I could catch the trim ring during a drive on a highway.
Logged

Dughr

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 65

    • CVO1: FLSTFSE '05
    • CVO2: FXSTSSE '07
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #3 on: March 07, 2012, 10:16:02 AM »

Awsome...thanks!   :2vrolijk_21:  Dental floss.  I can tell now that it isn't on by much...even though it is factiry original.  It is a bit disheartening though that the chrome is flaking off like a cheap platic model.  I don't think 4 years should rot Harley chrome.    :nixweiss:
Logged

Twolanerider

  • 25K CVO Member
  • *****
  • Offline Offline
  • Posts: 48951
  • EBCM #1.5 Emeritus DSP # ? Critter Gawker #?
    • MO


    • CVO1: 2000 Triple Red Screamin' Eagle Road Glide
    • CVO2: 2002 Candy Brandywine Screamin' Eagle Road King
    • CVO3: 1999 Arresting Red FXR2
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #4 on: March 07, 2012, 11:08:52 AM »

Awsome...thanks!   :2vrolijk_21:  Dental floss.  I can tell now that it isn't on by much...even though it is factiry original.  It is a bit disheartening though that the chrome is flaking off like a cheap platic model.  I don't think 4 years should rot Harley chrome.    :nixweiss:

Look the old one over very closely.  I vaguely remember some sort of alignment dot or arrow on the inside face or lip.  If it's there and orientation actually matters you'll want to lay the new one down with the dot facing the dame direction.
Logged

Screamin Eagle Carl

  • Livin' Large with Loud Pipes
  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 330

    • CVO1: 2008 Harley Davidson FXSTSSE2 CVO Screamin' Eagle Softail Springer
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #5 on: March 08, 2012, 11:09:19 AM »

Awsome...thanks!   :2vrolijk_21:  Dental floss.  I can tell now that it isn't on by much...even though it is factiry original.  It is a bit disheartening though that the chrome is flaking off like a cheap platic model.  I don't think 4 years should rot Harley chrome.    :nixweiss:

I think Harley subcontracts parts to China. My rearview mirror chrome is pitting. I will have to replace them. I suspect Harley's may be assembled in USA, not made in USA...

Carl
Logged
2008 Harley Davidson FXSTSSE2 CVO Screamin' Eagle Softail Springer
Livin' Large

Aussie

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 783


    • CVO1: FLHXSE3 Hot Citrus
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #6 on: March 08, 2012, 04:37:10 PM »

Cost cutting is very sad on a premium product, made in china assembled in US.
Logged

Dughr

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 65

    • CVO1: FLSTFSE '05
    • CVO2: FXSTSSE '07
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #7 on: March 22, 2012, 01:00:27 PM »

Turned out I only had to pull it up using finger nails and it came right off.  The new one went down easily after removing some old gummy glue from the first ring.  Its a simple replacement...although 13 bucks for a chromed piece of plastic....sheeeesh.
Logged

dlaws01

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1502
  • Rejoicing in hope, patient in tribulltion

    • CVO1: 105th Anniversary FXSTSSE2
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #8 on: March 22, 2012, 09:44:22 PM »

Yeah, but it's H-D chrome plastic made in china, so it's special!  ::)
Logged
Jesus is Lord

Screamin Eagle Carl

  • Livin' Large with Loud Pipes
  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 330

    • CVO1: 2008 Harley Davidson FXSTSSE2 CVO Screamin' Eagle Softail Springer
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #9 on: March 23, 2012, 01:20:22 PM »

I wonder if any MoCo board members are on this site? We should send them a letter. CVO's need American parts made with quality!
Logged
2008 Harley Davidson FXSTSSE2 CVO Screamin' Eagle Softail Springer
Livin' Large

CVO_Sam

  • Newbie
  • *
  • Offline Offline
  • Posts: 3
  • www.CVOHARLEY.com
    • OH


    • CVO1: 2014 Harley-Davidson FXSBSE - CVO Breakout
    • CVO2: 2019 Harley-Davidson FLHXSE - CVO Street Glide
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #10 on: July 09, 2018, 09:28:10 PM »

Turned out I only had to pull it up using finger nails and it came right off.  The new one went down easily after removing some old gummy glue from the first ring.  Its a simple replacement...although 13 bucks for a chromed piece of plastic....sheeeesh.

This method worked perfect me too. I simply pulled gently on the plastic trim ring after a long ride on a hot day and most of the glue came off. I used a little WD40 to remove the glue remaining then installed the new $13 plastic trim ring no problem. Let’s see if it stays on like it supposed to.
« Last Edit: July 10, 2018, 09:00:45 PM by CVO_Sam »
Logged

CHH_Badkarma

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 307
  • www.CVOHARLEY.com
    • CA


    • CVO1: 2014 CVO Breakout.
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #11 on: July 09, 2018, 09:47:31 PM »

About time for me to replace my trim ring also. The plastic chrome has flaked off from where the fuel nozzle touches from time to time.
Wish there was a better alternative that had the same clean look.
Logged

Dughr

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 65

    • CVO1: FLSTFSE '05
    • CVO2: FXSTSSE '07
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #12 on: July 10, 2018, 11:05:53 AM »

This method worked perfect me too. I simply pulled gently on the plastic trim ring after a long ride on a hot day and most of the glue came off. I used a little WD40 to remove the glue remaining then installed the new $13 plastic trim ring no problem. Let’s see if it stays on like it supposed to.
  6 years have passed and the ring I put on still looks brand new and has not given me a single issue.  I am very careful when adding fuel, but still, 6 years and it looks new is fine with me!
Logged

Jack

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 188
  • thank you Denis Van Orman (DVO)

    • CVO1: 07 FXSTSSE Amarillo Gold/Candy Tangerine (1/540) thanks Dude
    • CVO2: 98 Lincoln LSC Ivory Pearlescent (34K)
    • CVO3: 87 Porsche 944 Rose Quartz
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #13 on: October 03, 2018, 08:17:53 AM »

 :beatdeadhorse:

Picked up 3 (metal) rings few years ago in 2 ebay sales. Repl one easy to do, not following MoCo's instructions which
ask you to cut masking tape carefully with razor on tank. BS just align tape on two sides "L" shape to center.  Ring
(metal) is concave & will find its own seat by turning to fit BEFORE REMOVING TAPE.

Parts catalog says ( 63028-06 TRIM RING )

Never had problem after install providing you clean surface.

Careful filling still looks like new 3 ? years past.

Saw these plastic parts years ago, your call, metal still out there !.......J
Logged
FXSTSSE
H-D Tribal Mirrors (92410-09)
H-D medium low detachable (round stock) sissy bar
2006 Bobtail fender rack & trans dip stk w/medallion
Jet Scream (air delivery)
10mm SE plug wires
NGK Iridium IX (DCPR9EIX) 2316
Mercury Marine QUICKSILVER 20-W50
MOTORKOTE (petroleum hydrocarbon) in all 3 areas
RED LINE HEAVY SHOCKPROOF
93 Octane
Lyndall "Z" Racing Brake Pads "Gold"
(7059-G) ft
(7196-G) rr
H-D Crash Bar

JohnnieD

  • Johnnie D
  • Newbie
  • *
  • Offline Offline
  • Posts: 3
  • www.CVOHARLEY.com
    • PA

    • CVO1: '07 Softail Springer CVO
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #14 on: November 06, 2018, 09:40:20 PM »

I realize this thread is from 2012, BUT in case anyone looks it over... I replaced 2 of these rings and they stayed on just fine, for up to a week and a half at a time.  A buddy suggested getting Permatex gasket sealer which comes in blue (that matches my bike) and forget the crappy double sided tape that is NOT gas resistant.  That was two years ago and it is still going strong.
Logged
The secret of life is honesty and sincerity. If you can fake that, you've got it made.
Groucho Marx

skratch

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1866
    • LA

    • CVO1: 2013 FLTRXSE2 Roman Gold/Burnt Emerald
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #15 on: November 06, 2018, 09:48:27 PM »

i've had to replace mine for the plastic cracking or the chrome peeling, but i've never had a problem with the 3m tape not staying stuck.  maybe i just make sure that the surface is clean, and i don't try to overfill my tank.....
Logged
I understand the concept of reality, but find it too confining as a way of life

Jack

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 188
  • thank you Denis Van Orman (DVO)

    • CVO1: 07 FXSTSSE Amarillo Gold/Candy Tangerine (1/540) thanks Dude
    • CVO2: 98 Lincoln LSC Ivory Pearlescent (34K)
    • CVO3: 87 Porsche 944 Rose Quartz
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #16 on: November 07, 2018, 07:03:35 AM »

 :beatdeadhorse: 

If anyone is using plastic, it is not the correct part.

Metal trim rings are available (ebay), you get what you pay for if crap is what you want.

At 67,300 on the clock I had replaced the original years ago, second trim ring doing just fine, & have two (2) more replacements.



Logged
FXSTSSE
H-D Tribal Mirrors (92410-09)
H-D medium low detachable (round stock) sissy bar
2006 Bobtail fender rack & trans dip stk w/medallion
Jet Scream (air delivery)
10mm SE plug wires
NGK Iridium IX (DCPR9EIX) 2316
Mercury Marine QUICKSILVER 20-W50
MOTORKOTE (petroleum hydrocarbon) in all 3 areas
RED LINE HEAVY SHOCKPROOF
93 Octane
Lyndall "Z" Racing Brake Pads "Gold"
(7059-G) ft
(7196-G) rr
H-D Crash Bar

skratch

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1866
    • LA

    • CVO1: 2013 FLTRXSE2 Roman Gold/Burnt Emerald
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #17 on: November 07, 2018, 07:28:44 AM »

can you show me a link?  I was not able to find one.
Logged
I understand the concept of reality, but find it too confining as a way of life

Jack

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 188
  • thank you Denis Van Orman (DVO)

    • CVO1: 07 FXSTSSE Amarillo Gold/Candy Tangerine (1/540) thanks Dude
    • CVO2: 98 Lincoln LSC Ivory Pearlescent (34K)
    • CVO3: 87 Porsche 944 Rose Quartz
Re: Flush Mount Gas Cap Trim Ring Replacement
« Reply #18 on: November 07, 2018, 07:52:08 AM »

 :beatdeadhorse:

H-D part # 63028-06 chrome trim ring

At this moment it is not avail on ebay.

Place a (saved search) for this and one will show up in near future.......J
Logged
FXSTSSE
H-D Tribal Mirrors (92410-09)
H-D medium low detachable (round stock) sissy bar
2006 Bobtail fender rack & trans dip stk w/medallion
Jet Scream (air delivery)
10mm SE plug wires
NGK Iridium IX (DCPR9EIX) 2316
Mercury Marine QUICKSILVER 20-W50
MOTORKOTE (petroleum hydrocarbon) in all 3 areas
RED LINE HEAVY SHOCKPROOF
93 Octane
Lyndall "Z" Racing Brake Pads "Gold"
(7059-G) ft
(7196-G) rr
H-D Crash Bar
Pages: 1 2 [All]
 

Page created in 0.201 seconds with 24 queries.