Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: How do you remove the exhaust side floorboard?  (Read 1333 times)

0 Members and 1 Guest are viewing this topic.

Nicky Pass

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 856
How do you remove the exhaust side floorboard?
« on: May 15, 2015, 08:11:06 PM »

I got my spacer kit from Vance and Hines and the dealer is gonna put it on for free, but how hard is it?   
Logged

CowboyBagger

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1143
  • Standing on the Corner!
    • AZ


    • CVO1: FLHXSE3 Ruby Red/Typhoon Maroon
    • CVO2: FLTRKSEANV Heritage paint
Re: How do you remove the exhaust side floorboard?
« Reply #1 on: May 15, 2015, 09:56:12 PM »

I'm not sure what your spacer kit is, but to remove the driver floorboard it only requires the removal of two bolts that hold the bracket.  The pans are also attached by two bolts but you don't really need to remove them.

Cowboy
Logged
From an ocean tide, to an 8 second ride! Life is a ride, so make it a good one.

toddwebber

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 88
    • FL


    • CVO1: 2015 FLHXSE hard candy
    • CVO2: 2013 FXSBSE crimson
    • CVO3: 2012 FLHXSB (sold)
Re: How do you remove the exhaust side floorboard?
« Reply #2 on: May 16, 2015, 12:44:45 AM »

not hard at all. rear is just an allen bolt (I don't know the size without looking). Front is same sized allen bolt and 9/16 nut on the back side. Some blue loctite on the new bolts and your good to go. Very simple
Logged
Fuel Moto 113 big bore kit, Ward Performance CNC heads, Wood TW-999 cams, SE cam plate, Zippers chain tensioners, Darkhorse lower end, H beam rods, Timken bearing, SE 58mm TB, 5.3 injectors, AIM clutch, D&D Boarzilla 2/1, Dynojet Power Vision, Dynojet Target Tune, JRI rear shocks, Legend AXEO front shocks

ZVO

  • Dark Platimum? That’s Silver and Black
  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 369
  • www.CVOHARLEY.com
    • TX


    • CVO1: 2015 FLHXSE - Gone
    • CVO2: 2016 FLHXSE - Gone
    • CVO3: 2018 FLTRXSE - Gone
Re: How do you remove the exhaust side floorboard?
« Reply #3 on: May 17, 2015, 02:52:57 AM »

Their is also a spacer that is really tough to put in on the arm closest to the engine guard this space keeps your floorboard from touching your heat shield...make sure it goes back on because if not yoir right floorboard will have more vibration to it.

The dealer should be able to print out the schematic for you.
Logged
The Autumn Wind is a pirate.

Wild Hog 4

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 292
    • CVO3: 2018 CVO Road Glide
Re: How do you remove the exhaust side floorboard?
« Reply #4 on: May 17, 2015, 04:58:48 AM »

2 bolts and 5 minutes work,job done.!
The front arm causes no vibration issues at all even without spacers! and the spacer is only used at the front to bring the front of the board out parallel and square to the rear!
Logged
Ride free brothers!

Nicky Pass

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 856
Re: How do you remove the exhaust side floorboard?
« Reply #5 on: May 17, 2015, 09:50:25 AM »

The dealer put it on for me, and now I have to wait for the new heat shield and rear floor board arm.  Atleast you can't see it unless you are under the bike.
Logged
 

Page created in 0.214 seconds with 20 queries.