Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[hogdooz]

I'm trying to install the LED wrap around light bar off a 2011 FLTRUSE on my wifes FLTRSE3 tourpak. I got the Y-harness 70933-10 but it has non-sealed plugs and this bike has 8-pin Molex connectors for the rear lights. Does anyone know of a premade Y-harness or does anyone have the male and female Molex connectors I can get-new or used, I don't care. I would need the pins and sockets that fit them too. I'm trying to get this done before the Redwood Gathering in a couple weeks and my dealer takes about 2 weeks to get anything. If I can get the housings and pins, I can make this Y-harness I have work. Thanks for any help.

[Cvostu]

Try another dealer. . I ordered a harness from tri County Harley.  Took one week. Stuart

[hogdooz]

That's the problem about ordering from another dealer, I don't know the part number of the Y-harness I need. I think there should be one available but since the one I have isn't the right one, I don't have any other part numbers. The wires are correct in the one I have if I could get the 8-pin Molex connectors real fast, I could make the one I have work. Thanks for the response.

[TN]

Is this what yer looking for?


http://www.harley-davidson.com/store/switched-circuit-adapter-harness


I use this on my 09 when the tourpak is on, can't speak about fitment on an 2011

[hogdooz]

TN, thanks for the reply. No, this adapter is for the switched power accessories--I have that one. I need the one that breaks into the rear tail/brake light harness under the seat at the front of the rear fender--8-pin male and female Molex connectors for the light circuit harness with a 6-pin flat connector coming off it.

[TN]

Got ya, I know exactly what you speak of now. I use mine to light up the air wing light so I plug it in the rear taillight itself. I had to buy the connectors you speak of back when I installed a load equalizer in that place. Maybe Custom Dynamics could handle your request.


TN

[Joel]

This is not going to help, but when I had the tour pack and lights installed at the dealer on my 2012 CVO Street Glide, they said H-D didn't make a connector and they made there own, than I had to re-wire it so I could plug the original harness back in when the tour pack was off. Maybe talk to the service dept. to see if you can get the male and female connectors and pins to make your own.

[Cvostu]

There's a very talented guy on this forum. .  His name is Rich. . . He goes by tif2. . .  Great guy. . Send him a personal message. . He can make it for you. . I know he can do it. .  Stuart.

[CVODON]

I made mine, just went to the local elec supply store, they had the Molex connectors by the drawer full with the pins. Counting the drive it took a couple hours total. Cost $18.20 for supplies inc shrink tubing and grommets. This was for a LED strip on back of the t/p that I had Radiantz make for me, run in middle section, turn on outers and brake on all. I do not like the look of the wrap-a-round units, wish my new bike didn't have it, but to many holes in tourpak to fill if you try to remove it (I took it off to see). But making a harness is easy.

[hogdooz]

I took your advice, dug in and made my own y-harness, then finally figured out the flasher module wiring. Here is the final outcome--the wrap around LED light bar like on a 2011 FLTRUSE mounted on my wife's 2009 FLTRSE3 chopped tour pak. She is so happy! She liked the gray color, didn't want me to get it painted.

[Para Bellum]

Hogdooz, that looks really good. Always thought the TPs looked kinda bare without lights or anything else.