www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Hydraulic Clutch Slave Piston Movement when Replacing Whole Clutch  (Read 1831 times)

0 Members and 1 Guest are viewing this topic.

ltank

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1215
    • LA

    • CVO1: 2000 FXR4 S&S V111, CustomS.S. 2-1 exhaust, Primo-Rivera OD 6 speed, 49mm Custom Front End Ohlins 30mm Fork cartridges , Hyperpro Shocks, Barnett Scorpian Clutch
    • CVO2: 1983 88" Shovelhead Won the World of Wheels 1985 Sept 85 Issue of Hot Bike Mag
    • CVO3: 1989 FXRS, 1990 Custom 100" Shovelhead/ EVO
Hydraulic Clutch Slave Piston Movement when Replacing Whole Clutch
« on: April 17, 2021, 10:46:20 PM »
I had a Baker Hydraulic Clutch Cover and the Baker Clutch. I had the Clutch off for several days. When I installed the new Clutch there was a lot of Clutch drag. I guess the slave piston moved outwards and wouldn't allow a full disengagement. Pressure Plate travel was .057. I turned the adjustment inwards 1.5 turns and I was able to get .078" there is a slight dragon the new Clutch. The plates soaked in Spectro Harley primary oil for an hour. Tomorrow I'll test it off the stand if good on the driveway I'll take it out on the road. Is this normal? I wanted to make sure the EVO IND Stage-1 Terminator Clutch was working well before installing the AIM Lock-up Variable Pressure Plate.
« Last Edit: April 17, 2021, 10:48:57 PM by ltank »
Logged

ltank

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1215
    • LA

    • CVO1: 2000 FXR4 S&S V111, CustomS.S. 2-1 exhaust, Primo-Rivera OD 6 speed, 49mm Custom Front End Ohlins 30mm Fork cartridges , Hyperpro Shocks, Barnett Scorpian Clutch
    • CVO2: 1983 88" Shovelhead Won the World of Wheels 1985 Sept 85 Issue of Hot Bike Mag
    • CVO3: 1989 FXRS, 1990 Custom 100" Shovelhead/ EVO
Re: Hydraulic Clutch Slave Piston Movement when Replacing Whole Clutch
« Reply #1 on: April 17, 2021, 10:51:50 PM »
Baker hydraulic clutch setup uses thier heavy duty throughout bearing at the piston. Doesn't use a bearing in the Pressure plate like HD does. Won't have to buy special Pressure plate when converting  either way to or from a cable.
Logged

ltank

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1215
    • LA

    • CVO1: 2000 FXR4 S&S V111, CustomS.S. 2-1 exhaust, Primo-Rivera OD 6 speed, 49mm Custom Front End Ohlins 30mm Fork cartridges , Hyperpro Shocks, Barnett Scorpian Clutch
    • CVO2: 1983 88" Shovelhead Won the World of Wheels 1985 Sept 85 Issue of Hot Bike Mag
    • CVO3: 1989 FXRS, 1990 Custom 100" Shovelhead/ EVO
Re: Hydraulic Clutch Slave Piston Movement when Replacing Whole Clutch
« Reply #2 on: April 17, 2021, 11:50:14 PM »
Baker 6 Speed O.D. gearset,  5 quart oil pan and Form
Factor Slave Hydraulic Clutch Cover
Logged

ltank

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1215
    • LA

    • CVO1: 2000 FXR4 S&S V111, CustomS.S. 2-1 exhaust, Primo-Rivera OD 6 speed, 49mm Custom Front End Ohlins 30mm Fork cartridges , Hyperpro Shocks, Barnett Scorpian Clutch
    • CVO2: 1983 88" Shovelhead Won the World of Wheels 1985 Sept 85 Issue of Hot Bike Mag
    • CVO3: 1989 FXRS, 1990 Custom 100" Shovelhead/ EVO
Re: Hydraulic Clutch Slave Piston Movement when Replacing Whole Clutch
« Reply #3 on: April 18, 2021, 08:37:17 PM »
Does anyone know the best Hydraulic line I.D. ?
My clutch is still hard to Pull, I really can't tell any difference between the Hydraulic Clutch Pull and the Standard Clutch Cable Pul. I know there's a small Volume with the HD V-Rod 11/16" Master Cylinder.
Baker recommended 11/16" Master Cylinder  and AN3 fittings but instructions don't specify the Hydraulic hose? Thanks
Logged
 

Page created in 0.167 seconds with 20 queries.