Topic: Anbody got any ideas where this bolt may have come from (Read 2712 times)

Jon Seddon · « **Reply #15 on:** July 09, 2009, 11:41:42 AM »

Quote from: jiml on July 09, 2009, 11:00:07 AM

Maybe the threads might be too course for the fairing bolts? controls?

I'll keep on looking, most of the controls are chrome though?

Jon

hogasm · « **Reply #16 on:** July 10, 2009, 07:23:38 AM »

Quote from: hd-dude on July 08, 2009, 01:30:03 AM

That bolt is used for the inner fairing, two on each side, one pair down low above the lower tree and the other pair below the speakers area.

Jim is right

probably fell and the mechanic just got a new one instead of finding that one......did they charge you for a new one

Jon Seddon · « **Reply #17 on:** July 10, 2009, 07:27:19 AM »

Quote from: hogasm on July 10, 2009, 07:23:38 AM

Jim is right

probably fell and the mechanic just got a new one instead of finding that one......did they charge you for a new one

Nope and nobody admits to dropping one. Oh well, I hope nothing drops off.

Jon

hdctss · « **Reply #18 on:** July 16, 2009, 12:55:43 PM »

fairing bolt, but at least your dealer replaced two of them. Mine chose to only replace one black bolt with one silver bolt and then left the black one for me to find while I was cleaning the bike. this is the same kid who a couple of weeks later proceeded to do the 1K service and put formula+ in the primary and transmission instead of the Syn3. quality dealer service at it's finest...

Classic45 · « **Reply #19 on:** July 26, 2009, 05:07:31 PM »

Quote from: Jon Seddon on July 06, 2009, 12:22:38 PM

Any of you who've been follwoing the saga of the electrics on Big Bertha will know I've just got her back.

No electrical problems so far.

However, I washed the bike today for the first time since she came back, thought I'd check the rear seat bolt and sure enough it wasn't tight and even worse it was cross threaded. I had to get out my tap set to re tap the thread - I hope it will still stay tight. Every time my dealer takes the seat off they don't put it back on properly.

Also noticed that the dealer isn't as careful with my panniers as I am as now the bottoms are scratched as well as a light scratch on the sidepanel.

But the main thing is after washing the bike and refitting the seat I noticed a T27 black Torx bolt about 1/2" UH and 1/4" UNC, was not there before - obviously washing the bike has loosened it or it was under the seat somewhere. Any ideas where it's from??

Thanks in advance.

Jon

I do not trust my dealer, so I deliver my bike, when in need for service, without the panniers,- I have seen too much sloppy behaviour from the service department!

daycuse · « **Reply #20 on:** July 28, 2009, 08:29:18 PM »

It's mine, please send it back

Jon Seddon · « **Reply #21 on:** July 28, 2009, 10:04:28 PM »

It's in the post

Author Topic: Anbody got any ideas where this bolt may have come from (Read 2712 times)

Jon Seddon

Re: Anbody got any ideas where this bolt may have come from

hogasm

Re: Anbody got any ideas where this bolt may have come from

Jon Seddon

Re: Anbody got any ideas where this bolt may have come from

hdctss

Re: Anbody got any ideas where this bolt may have come from

Classic45

Re: Anbody got any ideas where this bolt may have come from

daycuse

Re: Anbody got any ideas where this bolt may have come from

Jon Seddon

Re: Anbody got any ideas where this bolt may have come from