www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: 2010 CVOUC - Tour Pak Position  (Read 1375 times)

0 Members and 1 Guest are viewing this topic.

lvse110se5

  • Las Vegas Rick
  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 140

    • CVO1: 2010 Ultra Classic
2010 CVOUC - Tour Pak Position
« on: October 23, 2009, 03:19:23 PM »
Does anyone know if there is a aftermarket item to allow you to move the tour pak back? It has three positions molded into the bottom of the tour pak, but it appears that it cannot be moved. Unfortunately, it is in the forward most position.
Logged

HOGMIKE

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2422
  • 65 FLH 93" + others
Re: 2010 CVOUC - Tour Pak Position
« Reply #1 on: October 23, 2009, 04:55:59 PM »
Quote from: lvse110se5 on October 23, 2009, 03:19:23 PM
Does anyone know if there is a aftermarket item to allow you to move the tour pak back? It has three positions molded into the bottom of the tour pak, but it appears that it cannot be moved. Unfortunately, it is in the forward most position.

In the service manual there is a section addressing that.
The box can be moved 1" forward or back. Pull up the liner and see the 4 mounting bolts and lock washers.
Logged
HOGMIKE

lvse110se5

  • Las Vegas Rick
  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 140

    • CVO1: 2010 Ultra Classic
Re: 2010 CVOUC - Tour Pak Position
« Reply #2 on: October 23, 2009, 05:00:12 PM »
Thanks, I will check again. I pulled the liner and looked at the bolts. The rack that it is attached to only has one set of holes, so that position is permanent, and the tour pak has a extra set of holes at the rear (not drilled) and none at the front of the tour pak. It appears to be unmoveable.
Logged

HOGMIKE

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 2422
  • 65 FLH 93" + others
Re: 2010 CVOUC - Tour Pak Position
« Reply #3 on: October 23, 2009, 05:16:04 PM »
Quote from: lvse110se5 on October 23, 2009, 05:00:12 PM
Thanks, I will check again. I pulled the liner and looked at the bolts. The rack that it is attached to only has one set of holes, so that position is permanent, and the tour pak has a extra set of holes at the rear (not drilled) and none at the front of the tour pak. It appears to be unmoveable.

The chromed rack has 4 threaded holes and the box has 2 sets of 4 holes for the bolts to go through. Our dealer has them set to the rear position unless requested differently.
Our '09's SE and Ultra were that way, my '10 is the same. Unless you have something a little different.
Check the bottom of your box, there should be a recess that will allow 1" fore and aft adjustment.
Hope this helps a bit.
Logged
HOGMIKE

OhioDave

  • 1K CVO Member
  • *
  • Offline Offline
  • Posts: 1073
    • OH

    • CVO1: 2015 CVO Limited
Re: 2010 CVOUC - Tour Pak Position
« Reply #4 on: October 23, 2009, 05:30:07 PM »
Try this for a great aftermarket product.

http://www.cvoharley.com/smf/index.php?topic=14276.0
Logged

rbaker

  • Elite CVO Member
  • *****
  • Offline Offline
  • Posts: 770
    • AZ


    • CVO1: 2007 FXSTSSE
    • CVO2: 2010 FLHTCUSE5
Re: 2010 CVOUC - Tour Pak Position
« Reply #5 on: October 25, 2009, 05:00:40 PM »
http://www.tourpaks.com/productdetail.php?item=100462&name=Tour-Pak Relocator for H-D 2009 & 2010 FLH Series & Screaming Eagle


More info and picture and instructions.

Richard
Logged

lvse110se5

  • Las Vegas Rick
  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 140

    • CVO1: 2010 Ultra Classic
Re: 2010 CVOUC - Tour Pak Position
« Reply #6 on: October 26, 2009, 03:02:06 PM »
Thanks guys, i just ordered one from George. :)
Logged
 

Page created in 0.217 seconds with 21 queries.