Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[JDOFLHRIDER]

You will  need 69911-11 and 70933-10 and pages 1thru 3 posted below.TOOLS NEEDED  1)SMALL NEEDLENOSE PLYERS,2)REALLY SMALL DRILL ,PAPERCLIP OR JEWELERS SCREW DRIVER,3) BLACK TAPE ,4) WIRE TIES                                              1)YOU NEED TO TAKE SEAT OFF AND TOUPACK LINER OUT.                                                           2)NEXT UNPLUG TAIL LIGHT PLUG AT REAR OF TOURPAC.  (SHOULD BE 7 WIRES BLACK,VIOLET,AND BLUE.) THIS IS PLUG YOU HAVE TO REALIGN WIRES IN.                     3) DISASSEMBLE TAILIGHT PLUG  ,USE SMALL NEEDLE NOSE TO CLICK PULL WHITE CENTER OUT IN TAILIGHT PLUG ,IT JUST COMES OUT A LITTLE TO UNLOCK .  THEN USE A SMALL ROUND TOOL(PAPER CLIP,JEWELER SCREWDRIVER,OR DRILL) TO PUSH IN ROUND HOLE IN PLUG TO RELEASE THE WIRE, DO TO ALL THE WIRES IN THE PLUG.       4) WHEN WIRES ARE OUT OF THE PLUG YOU NEED TO TEST AND MARK  LEFT , RIGHT,AND MIDDLE SO YOU CAN REALIGN BACK IN PLUG .HARLEY PAGE 2-5  I COPIED AND MARKED #1  THE PICTURE OF PLUG IS FROM REAR. (WIRES  SHOULD SNAP  BACK IN)                                                                                                                                                              5)   FEED MODULE WIRES THRU  TOUR PAK   (I TAPED MINE TO FEED OUT OF LEFT SIDE SO I COULD PUT MODULE IN BUMP OF LINER)                                                                               6 )TAKE Y HARNESS AND PART LOOSE  PLUG ON IT AND  MATCH WIRE COLORS TO EACH OTHER (except yellow to red,white to blue or no wire) ,WIRES SHOULD CLICK IN  DO NOT FORCE.                                                         7 ) INSTALL Y HARNESS AND POSISION WIRING  TO  TOURPAK AND IN TOURPAK  AND PLUG TAILIGHTS IN. YOU MIGHT HAVE TO USE LINER TO FIND RIGHT SPOT FOR MODULE,                                                                                                                                                   8)WIRE TIE AND TEST  GOOD LUCK JDO

[JDOFLHRIDER]

second 2010 kit pg

[JDOFLHRIDER]

third pg

[JDOFLHRIDER]

FOURTH PG

[JDOFLHRIDER]

FIFTH PG

[JDOFLHRIDER]

2011 KIT PG 1

[JDOFLHRIDER]

2011 PG 2

[JDOFLHRIDER]

2011 PG 3

[JDOFLHRIDER]

2011 PG 4

[JDOFLHRIDER]

2011 PG 5     Last page of both 2010 and 2011 kits part 69911-11 looks the part that makes turn signals on our 2010 seuc's

[bikerboy53]

Has anybody tried to get the harness yet? I have a crimper that allows me to make my own "factory style" wiring -maybe this is something we could figure out and make on our own? Or is the feed harness from the bike different too?

I've looked at the similar "magic converter" product from customdynamics, and I think they require the installation of a run/turn/brake conversion module to make their harness work. I wonder if something like that is needed here for the 2010s too? I don't know enough about the new '11 SEUC lights/turn signals to make any guesses yet... The customdynamics part is at:

http://www.customdynamics.com/hd_tour_pak_led_lighting.htm#Magic™_Converter_for_Harley_Davidson®_Tour_Pak®_

It would be nice to make the T-Pak side lights into run/turn lights too. It looks like the customdynamics harness allows that function.
 

[JDOFLHRIDER]

part doesn't show up yet,I was gonna match a 2010 and 2011 parts book to see if same part. disclaimer on above part (previous reply) says won't work on S E led tourpak lights.I know leds are harder to work with.

[bikerboy53]

Thanks for the info -looks like I missed the (not so) fine print on the customdynamics website!  And TIA for any additional information you can come up with for the HD approach.

I never understood to begin with why HD didn't come out with run/turn/brake on the two LED lights next to the center brake light. I guess this way they get to sell us more stuff! 

[Opossum]

I had the shop install the run/brake/turn module on my scooter and the shop pigtailed two wires to the tour pack lights and they now blink w/the turn signals.  not so bright in the day but great at night.  I think it's just run two wires and done.  They charged me 1/2 hour labor so for me no brainer.

[JDOFLHRIDER]

i talked to a guy that uses a micro proccessor to work leds flashing ,I'm wonder if harley hardwires or uses a micro processor.when i get more info i'll update.