www.CVOHARLEY.com

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: 09 LED tail light - brake light not working  (Read 14614 times)

0 Members and 1 Guest are viewing this topic.

Zinister

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 256

    • CVO1: 2009 FXSTSSE3
09 LED tail light - brake light not working
« on: August 12, 2012, 01:32:30 PM »
My tail light is on but doesn't get brighter when brakes applied. Any ideas on what to look for?

I've already looked at all the fuses and for bad connections/rubbing wires.
Logged

TLC

  • Junior CVO Member
  • **
  • Offline Offline
  • Posts: 54

    • CVO1: 09 FXSTSSE3
Re: 09 LED tail light - brake light not working
« Reply #1 on: August 13, 2012, 09:34:06 PM »
Mine quit working when applying brakes and just quit altogether then would come on if I hit a bump in the road.Dealer said others were bad too.Luckily was under warranty and just plugged new one in and been fine for 2 years on the FXSTSSE3.Rode over to Savannah last weekend to Iron horse and Poopys.Nice ride.2 V-8 Chopper trikes pulled in,nice looking rides.
Logged

Zinister

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 256

    • CVO1: 2009 FXSTSSE3
Re: 09 LED tail light - brake light not working
« Reply #2 on: August 13, 2012, 11:03:04 PM »
That's funny, I was at both places on Saturday. I stand corrected on my light. I think my light is on the bright setting at all times like the brakes are being applied.

Checking out the brake switches this week.
Logged

Zinister

  • Senior CVO Member
  • ****
  • Offline Offline
  • Posts: 256

    • CVO1: 2009 FXSTSSE3
Re: 09 LED tail light - brake light not working
« Reply #3 on: September 13, 2012, 08:06:20 PM »
I found out my rear brake pressure switch is bad. Wasn't this a problem on the baggers?
Logged

DarkEagle

  • Full CVO Member
  • ***
  • Offline Offline
  • Posts: 110

    • CVO1: 2009 FXSTSSE3 Black Diamond with Emerald Ice Flames
Re: 09 LED tail light - brake light not working
« Reply #4 on: September 15, 2012, 01:44:22 PM »
1st time I noticed, brake light stayed on from my front brake lever. If I pushed lever out, it turned off, but back on sometimes when I let pressure off. Dealer replaced master cylinder on warranty and fixed it.

Just past month it started again, found by working lever it turned off. Being careful with the paint job, I tried spraying WD40 around brake switch & master cylinder plunger, doesn't stick as much. Brakes ready for replacement so I plan to take part of lever apart to clean & lightly lube all moving parts & run clean brake fluid through all the lines to see if that will fix it.

I'm thinking the master cylinder's internal spring on the plunger isn't very strong but now wonder about the brake sensor switches, probably all made in China...

Thanks for sharing!
Logged

2k

  • My ignorance is just as good as your knowledge, when my information changes, I alter my conclusions
  • 5k CVO Member
  • ***
  • Offline Offline
  • Posts: 7996
  • monter le cheval de fer (French)
    • NC


    • CVO1: 2013 SERK-Dressed in BLUE of course.
    • CVO2: 2002 Supercharged HD F150 512 RWHP
    • CVO3: 1956 BelAir Sports Coupe
Re: 09 LED tail light - brake light not working
« Reply #5 on: September 27, 2012, 09:22:44 PM »
Quote from: Zinister on September 13, 2012, 08:06:20 PM
I found out my rear brake pressure switch is bad. Wasn't this a problem on the baggers?

It wound up being a recall for the baggers.......I would argue that point with the shop!!!
Logged
Most Honda Goldwing riders will blink when hit in the head  with a ball-peen hammer (sans helmet)

nevinlee

  • Newbie
  • *
  • Offline Offline
  • Posts: 1
Re: 09 LED tail light - brake light not working
« Reply #6 on: December 19, 2012, 10:38:16 PM »
The problem might be in brake switch, or lose connection inside the light itself, not the wiring that connects it. Try checking that also.
_______________________
led work lights
Logged

Engz16

  • Newbie
  • *
  • Offline Offline
  • Posts: 3

    • CVO1: 2008 FXSTSSE2 CVO Softail Springer
Re: 09 LED tail light - brake light not working
« Reply #7 on: May 08, 2013, 04:40:40 PM »
I had the same problem with my 08. Took the tailight apart and where the 2 boards attach together for the license plate light and brake light the connector solder joint was broken. It was hard to find but its the bottom of the black connector between the 2 boards. If you lift on it you should be able to tell if its broken. Should have taken a photo. Got out the soldering iron and resoldered. took about 1/2 hour. no problems since.
Logged

Massiah

  • Newbie
  • *
  • Offline Offline
  • Posts: 2
Re: 09 LED tail light - brake light not working
« Reply #8 on: January 30, 2014, 12:07:16 AM »
I'm having the same issue, ordered  a replacement off ebay, had the same problem...hmmm any fixes yet?
Logged
 

Page created in 0.217 seconds with 20 queries.