Topic: 14 SERK lifters replacement (Read 1863 times)

Qnn · « **on:** May 21, 2018, 04:20:24 PM »

I have 14 SERK with about 21k miles on it and planning to replace cam bearings, tappets and pushrods with SS products. Just to be sure. Which tappets do you suggest ? Premium with limiters seems to be mostly suggested here, and which pushrods from SS ? HD dealer says that there is difference between 13 and 14 SERK but SS catalogs dont show it. Sorry for my english not my everyday language.

fastfreddy · « **Reply #1 on:** May 21, 2018, 05:46:45 PM »

my thoughts are you don't need limiters unless you have a cam with over .600 lift, I just replaced mine in the 16 with premium s&s and used stock push rods

grc · « **Reply #2 on:** May 21, 2018, 07:33:22 PM »

There is no mechanical difference between the 2013 and 2014 valve train or engines for that matter, the differences between the two model years involve the electrical system (HDLAN or CAN bus being the biggest difference) and things like suspension. Look up Harley Rushmore for details of those changes.

The regular S&S lifters or the S&S Premiums come highly recommended. You do not need the ones with travel limiters.

Jerry

ultra13 · « **Reply #3 on:** May 21, 2018, 08:39:51 PM »

Yes....S&S Premiums and stock pushrods...

KGB · « **Reply #4 on:** May 21, 2018, 08:42:25 PM »

I used S&S premium with quickie push rods, that way, if I wanted to put a cam in later, I don't have to pull the top end apart, I also thru in rocker lockers.

Boatman · « **Reply #5 on:** May 21, 2018, 11:12:34 PM »

Quote from: ultra13 on May 21, 2018, 08:39:51 PM

Yes....S&S Premiums and stock pushrods...

X2 as that is what I did at less than 20K on my 2014.. Asked Steve at Fullsac and he does not do adjustables so that was ok with me. No limiters. Good luck.

Qnn · « **Reply #6 on:** May 23, 2018, 05:10:07 AM »

I went with https://www.sscycle.com/products/high-performance-hydraulic-tappets-for-1999-17-big-twins-and-2000-18-hd-sportster-and-2017-18-m8-models/
and http://www.dragspecialties.com/products/?productId=479175&partNumber=09280051

ultra13 · « **Reply #7 on:** May 23, 2018, 04:58:07 PM »

Good choice on the lifters. Replaced mine at 19,000 miles.....Common point of failure it seems.

MCE · « **Reply #8 on:** May 30, 2018, 07:30:35 PM »

I like S&S' lifters. Their low-end ones are as good or better than most. Johnson hylift are very good too. fwtw

Qnn · « **Reply #9 on:** June 06, 2018, 06:44:11 AM »

Work is done now. Old lifters were OK, no recognizable wear or loose bearing. However, feels good to have them out. Cam bearing were ok also, but swapped anyway. Good thing is that oil pump, chain and tensioner were checked also and all perfect. Those SS time saver pushrods dont need new covers but adjusting is VERY uncomfortable, mechanic with very little girly hands may find it OK

Local HD dealer mechanic was very frustrated

but got it done finally. Engine seems to run a bit quieter. 34k km on the clock.

J.D. · « **Reply #10 on:** June 06, 2018, 07:52:42 AM »

Fueling makes a little pushrod tube holder tool that makes the adjustables easy to install when using the stock pushrod tubes.

Author Topic: 14 SERK lifters replacement (Read 1863 times)

Qnn

14 SERK lifters replacement

fastfreddy

Re: 14 SERK lifters replacement

grc

Re: 14 SERK lifters replacement

ultra13

Re: 14 SERK lifters replacement

KGB

Re: 14 SERK lifters replacement

Boatman

Re: 14 SERK lifters replacement

Qnn

Re: 14 SERK lifters replacement

ultra13

Re: 14 SERK lifters replacement

MCE

Re: 14 SERK lifters replacement

Qnn

Re: 14 SERK lifters replacement

J.D.

Re: 14 SERK lifters replacement